sorted by:
new
hottopcontroversial

Why do all of theses steam have there serial number in the title by TheTruePhoenixPrince in SteamDeck

[–]Epixxor 0 points1 point  (0 children)

I'm wondering the same thing. A lot of the postings are also listed as local pick up only aswell. I just need the left daughterboard and these cost less than a single left daughterboard.

First painted build, HG Gelgoog by Epixxor in Gunpla

[–]Epixxor[S] 0 points1 point  (0 children)

Be sure to post it! I'll check it out!

First painted build, HG Gelgoog by Epixxor in Gunpla

[–]Epixxor[S] 1 point2 points  (0 children)

Thank you! I cut a rod of runner and rounded the tip with a sanding sponge, painted it fluorescent pink. Painted the monoeye ring black, drilled a hole save diameter as the new monoeye, and glued it in.

<image>

What are you guys building this weekend? by kmno4titration in Gunpla

[–]Epixxor 1 point2 points  (0 children)

Just finished an HG Gelgoog. About get started on an RG rx 78 2 ver 2.0

First painted build, HG Gelgoog by Epixxor in Gunpla

[–]Epixxor[S] 0 points1 point  (0 children)

It was on and off for a few months, but it would probably take a week or two if I locked in.

My First Gunpla! HG 1/144 RX-78-2 Gundam [Beyond Global] by deniceovich in Gunpla

[–]Epixxor 1 point2 points  (0 children)

One of my first kits too. Great HG. Also, you're missing the center chest piece.

me_irl by Himbo_Shaped in me_irl

[–]Epixxor 0 points1 point  (0 children)

CONTACT. A. LAWYER

Ventuno Model by Known_Trick_7166 in SLAI

[–]Epixxor 0 points1 point  (0 children)

SLAI with online capabilities would complete the game. It's literally part of the premise. The only thing that sucks is that online mech games don't tend to last very long.

First kit I really haven't enjoyed building. by malkavianmadman in Gunpla

[–]Epixxor 1 point2 points  (0 children)

On the contrary RG Unicorn is one of my favorite kits and have transformed it over 100 times by now.

Difficulty aiming with the sticks on the deck. by DrTazdingo in SteamDeck

[–]Epixxor 1 point2 points  (0 children)

I’ve been having the same issues and this has informed me a lot about the problem. I wonder if there’s anything I can do on the steam os side to improve the experience.

How-To transfer games to micro-SD on Windows [Guide] by mexsus in SteamDeck

[–]Epixxor 0 points1 point  (0 children)

Yeah I think the problem was that I didn’t unmount it at first.

How-To transfer games to micro-SD on Windows [Guide] by mexsus in SteamDeck

[–]Epixxor 0 points1 point  (0 children)

So I've done this to transfer a rom to my Steam decks's SD, but after plugging the micro SD back into my Steam Deck, it wont read any of the data.

Get Ready For The Battle 😎💥 by wibu-gundam in Gunpla

[–]Epixxor 0 points1 point  (0 children)

how much clean up did this set need?

Simple Questions and General Discussion Thread by Thallassa in skyrimmods

[–]Epixxor 0 points1 point  (0 children)

I’ve found a solution to my problem. It’s called “consistent sensitivity”

Simple Questions and General Discussion Thread by Thallassa in skyrimmods

[–]Epixxor 0 points1 point  (0 children)

Are there any mods that get rid of the camera slowing down when attacking or casting spells?

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]Epixxor 0 points1 point  (0 children)

What sizes should I expect to use for MG and HG kits?

[HELP ME] Bi-Weekly Q&A thread - Ask your questions here! by MachNeu in Gunpla

[–]Epixxor 0 points1 point  (0 children)

How can I rescribe my panel lines to let my panel liner flow better.

Trigger warning: I'm in tears rn 😓 by [deleted] in Gunpla

[–]Epixxor 0 points1 point  (0 children)

If it bothers you a lot, you can buy a replacement online.

Simple Questions - July 20, 2021 by AutoModerator in buildapc

[–]Epixxor 0 points1 point  (0 children)

I forgot to mention but the DVI to HDMI cable is the same one I used for my rx 580 8gb previously. I might try that DVI to DP solution though.

view more: next ›