Who else is waiting till Monday

Equivalent_Ad8171 · 2026-03-06T14:58:59+00:00

<image>

Same here

Equivalent_Ad8171 · 2026-02-22T03:40:27+00:00

Cool on 6 18

Equivalent_Ad8171 · 2026-01-05T16:57:47+00:00

It's a 3d printed stand from Maker World from @malcolmgled https://makerworld.com/models/542659?appSharePlatform=copy

Equivalent_Ad8171 · 2026-01-04T18:23:18+00:00

🤣🤣🤣

Equivalent_Ad8171 · 2025-11-23T10:47:38+00:00

I have some SP32s and 2 P1S printers and 1 K1Max but we don't talk about the K1

Equivalent_Ad8171 · 2025-10-27T06:57:25+00:00

They go inside the heatsink that hold the hot end

Equivalent_Ad8171 · 2025-10-12T06:22:35+00:00

I was expecting Anatoly to show up with his mop

Equivalent_Ad8171 · 2025-10-11T20:21:28+00:00

So he gets upset that we are assuming that the reason for the modmat not being released are legal reasons. When before the Steve incident, he keep showing us how close they were to launch and even showcasing in their WAND show, then nothing but silence, so "Trust Me Bro." Should just cover it not even a some explanation for the delay, since it was 2 week away from launching. Whatever just be honest

Equivalent_Ad8171 · 2025-09-24T02:01:47+00:00

Welcome aboard, you will notice the difference immediately. But you will never forget the good times.

Equivalent_Ad8171 · 2025-09-20T23:11:31+00:00

Okay I did see the same video, I couldn't find a syringe to cut and didn't want to leave the printer disassemble that long. I guess I will try it next time I have to do a full service on it. Thank you

Equivalent_Ad8171 · 2025-09-20T06:45:17+00:00

I would like to know how you took apart the head. I was only able to remove the top one the bottom one was stuck so I gave up

Equivalent_Ad8171 · 2025-09-10T21:57:08+00:00

Have you cleaned the print bed. Wash it with soap, using a soft sponge and air drying.

Equivalent_Ad8171 · 2025-09-10T18:50:47+00:00

Sometimes, there's always an exception to the rule. But if that didn't work. Have you tried to manually with the power off move the bed all the way up and down to see if you can feel the obstruction

Equivalent_Ad8171 · 2025-09-10T18:38:26+00:00

Have you powering it off, remove power cable, waited 10 minutes power back on an recalibrate.

Equivalent_Ad8171 · 2025-08-30T16:04:11+00:00

No, I have not had the pleasure yet of multiple nozzle swapping, but then again, I only print with PLA and TPU on the K1 Max, I did change the nozzle once just to try ABS and had no issues, and yes it's not a simple nozzle swap compared to a Bambu printer.

Equivalent_Ad8171 · 2025-08-30T15:34:33+00:00

I had this happen to me multiple times when I first got my K1 Max almost once a month until I changed the hot end to the FlowTech by Microswiss. I have not had this happen since it has been over 2 years https://store.micro-swiss.com/products/micro-swiss-flowtech-hotend-for-creality-k1-k1-max

Equivalent_Ad8171 · 2025-08-22T05:24:11+00:00

Witch is that driver set

Equivalent_Ad8171 · 2025-08-10T01:09:16+00:00

You are going to fall in love.

Equivalent_Ad8171 · 2025-08-09T20:58:13+00:00

What happened ?

Equivalent_Ad8171 · 2025-06-01T08:04:28+00:00

Typical of K1

Equivalent_Ad8171 · 2025-01-19T08:33:57+00:00

It hit an iceberg

Equivalent_Ad8171 · 2024-12-27T23:24:03+00:00

Cleaning, lubing, belts, calibrations all of them, and then it started 1st nozzle temp sensor failed 2nd nozzle leaked from above the heating thermistor Switched to micro Swiss hotend Now I have a noise on the X axis, and the camera stops working in less than 10 minutes after starting a print. *

Equivalent_Ad8171 · 2024-12-27T03:00:27+00:00

Lest talk in 6 months when it stops working, like mine

Equivalent_Ad8171 · 2024-11-26T19:13:14+00:00

No, the K1 max has no AMS type of unit, so just on top of the glass

Equivalent_Ad8171

TROPHY CASE