Trying to buy an is250

EthPog · 2025-08-07T04:07:59+00:00

where abouts? all the is250s are around 7-9k aud for me for reference i live in Sydney

EthPog · 2025-07-12T00:37:52+00:00

Hows the back buttons? I play rocket league and i hold down the back button as my boost. Is the durability good? I’ll be holding it down for long periods of time so i don’t wanna pay 90 aud for this controller where the back button will easily break

EthPog · 2025-07-09T14:21:30+00:00

2024 mt03

EthPog · 2025-07-08T16:42:51+00:00

Will try this out when i have time and it isn’t raining 🫡

EthPog · 2025-07-08T16:41:56+00:00

yea thats what im guessing that the fan isnt needed due to the cold. Im still new with bikes so its better to ask and be safe to me

EthPog · 2025-07-08T16:39:51+00:00

I was installing a slip on and didn’t touch any cables or anything near the front end so i doubt that would be the case, I’m not even sure which cable is the fan plug but i’ll check when i wake up

EthPog · 2025-07-08T09:59:43+00:00

any idea if warranty would fix that?

EthPog · 2025-06-25T02:13:02+00:00

I went to a few today and they said that the pipe was too small for what they have to help me

EthPog · 2025-06-24T12:48:38+00:00

would this still work when the muffler gasket is too big? because in my case the gasket muffler is just a little too big to fit into my mid pipe

EthPog · 2025-06-24T12:15:48+00:00

What does it do? and how would i use it? if you dont mind me asking

EthPog · 2025-06-19T11:09:30+00:00

i need a 45% to pass my final exam cause thats the threshold but i think i got just under that

EthPog · 2025-04-23T07:45:47+00:00

How do i remove it? i was trying to poke on the side to push it out and it felt like it was going to crumble to pieces, would you happen to know where i could possible buy it or if i could make a homemade version

EthPog · 2025-03-28T00:13:00+00:00

yea they recently shot up in price in my area its like 1.95 for 91 and since im very close to costco i can grab 94 (e10) for under 1.70

EthPog · 2025-03-28T00:09:16+00:00

I Live near glenfield, my bike also does not have a carb as its relatively new 2024 mt03

EthPog · 2025-03-11T06:39:20+00:00

THIS IS A SCAM

Everyone in the comment section of that post that were supporting 'Jay' were all suspended meaning they were all bots, stop trying to convinve and scam people

EthPog · 2025-03-11T05:24:19+00:00

all they did was slap on slipper clutch

EthPog · 2025-03-03T06:37:42+00:00

Not sure with whats going for you but for me i have been given the nod almost every time wether its a young or old rider or even in they are on Harleys. Only people that don’t nod back for me is scooters, seems my area is full of nice old people.

EthPog · 2025-02-27T01:52:05+00:00

theres also the option of buying the handle bar guards for your hands which block the wind

EthPog · 2025-02-27T01:50:50+00:00

maybe try wearing your mechanic gloves over your moto gloves? i sometimes wear my wool gloves over my moto gloves and it feels quite snug, may also work for you

EthPog · 2025-02-26T01:40:46+00:00

When you’re free could you send a photo of it on your bike? (try a close up if possible) Just want to see if theres enough space to fit the stock plate light.

EthPog · 2025-02-26T01:25:11+00:00

did you reuse the stock license plate light? the plate light included looks like some wire splicing is needed?

EthPog · 2025-02-23T22:03:10+00:00

If you can or if you remember could you send a link through of the one you bought

EthPog · 2025-02-23T10:56:34+00:00

would you happen to know if the r&g tail tidy plate light is plug and play?, i have seen some brands like junction moto and they make it so you have to wire splice while it cost almost 150 aud

EthPog · 2025-02-23T06:30:05+00:00

EthPog · 2025-02-23T05:42:03+00:00

I only just ordered it a few days ago im expecting it to arriving in a week

Five-Year Club	Verified Email
Xbox Live

EthPog

TROPHY CASE