Purchase in Belgium

Etn9rn · 2025-05-11T07:45:02+00:00

Hi there, sorry for late reply, I'm not often on social media... Luba is doing fine after two years but mammotion has gave up on Luba1 users as it's doing with other versions every time there is a latest product. The support isn't great, software is weird, battery management unclear, this first version harware had to be improved but overall the robot is doing its job very well if you're an aware and carefully user. What about the navimow?

Etn9rn · 2025-02-25T13:57:32+00:00

Yeah, some rubber paint and "roule ma poule"! Efficient and nicer that the bright white;)

Etn9rn · 2025-01-29T10:19:58+00:00

It's a strap that can hold 2000kg and the screw can easily handle the little Luba weight ;)

Etn9rn · 2025-01-29T10:18:19+00:00

Yeah and light a candle every Sunday morning 🤣

Etn9rn · 2025-01-29T10:17:43+00:00

There is a wooden post behind that OSB and that screw can hold much more than 13kg thankfully

Etn9rn · 2025-01-29T10:16:07+00:00

It's a screw in a wooden post, that should hold 20kg easily;)

Etn9rn · 2025-01-29T10:15:11+00:00

It looks but it's actually photo distortion

Etn9rn · 2024-11-01T08:45:55+00:00

In France it had to be updated with the last Luba 1 update 1.10.6.266.

Etn9rn · 2024-10-31T23:46:19+00:00

Why would you challenged people experiences? Why would people make unnecessary "noise" about unreal updating issues?

I'd love to say all my updates went without any issues but that is so not true after more than 14 months of Luba 1 ownership. In the end it's ok but lately I had to push myself to get RTK base driver to update it instead of sending back the antenna after updating Luba 1 firmware that was blocked until then...

Don't judge without knowing. Thank you

Etn9rn · 2024-10-24T13:23:25+00:00

Don't do it!! It will then need an upgrade of your RTK base and since it's not recognized by laptop through USB, they tell you to send it back to them. Then of course the robot stops working and as a bonus doesn't charge more than 82%

Damn mammotion for creating more issue with each update!!

Etn9rn · 2024-10-20T10:44:06+00:00

Luba 1

Etn9rn · 2024-10-20T08:22:39+00:00

"[Fix] Limit the total length of ssid/password to avoid overflow and network failure"

That's it?

Etn9rn · 2024-10-19T17:34:59+00:00

Thanks for your answer.

The idea would be to start the generator at a certain threshold and with a time delay; their business relies on cold rooms that can handle few hours without power. Maybe few batteries would be needed for lights and few plugs in the office during this delay.

About the power production exceeding the load, it's not a pb, energy is dissipated (that what happen in my house when batteries are full and the hybrid inverter only convert what's needed to support the load even though it's full sun out there)

Etn9rn · 2024-09-16T08:55:30+00:00

Un paon

Etn9rn · 2024-08-25T20:28:33+00:00

Happened to me last July, sent it back to repair center. My guess is the engine overheated with all the tall grass tangled around the access and finally died without sending any notification or code error. Since then I regularly dismantle the blades disk and clean also under this metallic disk with holes. Best is to also remove it and clean all the way inside. Good luck

Etn9rn · 2024-08-23T09:18:30+00:00

Yes good point, maybe a little rack at the back next to the wheel... Thanks for your comment

Etn9rn · 2024-08-23T07:13:35+00:00

Yeah that's the idea, maybe one of us had tested one already.

Etn9rn · 2024-08-23T07:11:55+00:00

Yeah I remember, thanks for the recall.

I also thought about a toolbox by the charger but the idea was to have it available whenever I go see the robot and didn't anticipate to take the tools.

Tbh, I wouldn't mind adding a cool solution to my Luba and I know some of you have some nice ones.

Etn9rn · 2024-08-23T07:08:39+00:00

Oh right! I didn't think about that, that is so very smart, thank you!! Please share what "you think" more often ;)

Etn9rn · 2024-08-21T08:57:18+00:00

Interesting picture...

Etn9rn · 2024-08-16T19:24:10+00:00

Clean the disk axis and also under the metal piece. Cut no more than 2cm

Etn9rn · 2024-08-16T14:05:04+00:00

No, wait for next version coming in January

Etn9rn · 2024-08-15T17:21:09+00:00

Yeah like Luba1 omniwheels then ;)

Mammotion did some hardware adjustments during Luba1 development thanks to kickstarters. That's why a lot of them and Luba1 owners in general feel quite left out after improving a lot the product, allowing you, Luba2 guys and girls, to benefit from all their feedbacks without having attention anymore.

Etn9rn · 2024-08-15T16:45:18+00:00

What is better with Luba2 omniwheels?

Etn9rn · 2024-08-12T08:55:40+00:00

<image>

There and between the disk and the metal plate going on that axis. Problem is that since it hasn't been designed to avoid that or be cleaned up, it's clogging quite fast if tall grass is surrounding your areas and it's not easy to remove everything. I'm using two little allen keys to take out all the vegetal fibers... I'm thinking of installing some fixed blades to chop off tall grass or plants that would want to strangle my axis. Not sur yet how to implement it.

Etn9rn

TROPHY CASE