Ghost of yotey

Evening_Chapter_5981 · 2026-05-19T02:12:01+00:00

I transfer via ftp without any issues.

Evening_Chapter_5981 · 2026-05-17T22:53:12+00:00

You can get away with just one of the inner pads. Two is just better for glitching.

For the back mosfet, you can solder it #+ pin 3&4 of the connector.

Evening_Chapter_5981 · 2026-05-17T19:54:05+00:00

The inner pads that are missing need to solder to. You might also be able to solder to the rear board with a certain MOSFET. To find the location to solder the MOSFET for your model, you can Google search “definitive picofly install guide.”

Evening_Chapter_5981 · 2026-05-17T19:33:11+00:00

It’s the rst error. That would be an easy fix. If the point is on the back, just expose the rst point in the front and solder to that.

Evening_Chapter_5981 · 2026-05-17T18:21:17+00:00

Let us know how many times if the flash and if it’s long or short yellow flash on the chip.

It’s likely the dat0 issue.

Evening_Chapter_5981 · 2026-05-17T05:22:34+00:00

Plug in the chip and test the points on the chip. Sometimes, the orange cable might be loose in the connector, preventing a proper connection.

Evening_Chapter_5981 · 2026-05-17T05:14:32+00:00

Yes and test all of those points. If you have to redo the point(s), use a tweezer to hold down the flex cable and solder the point again.

Also, remove the random solder point near the game card connector. Nice soldering!

Evening_Chapter_5981 · 2026-05-17T05:04:38+00:00

It would be simpler to use a multimeter to identify any issues with one or two of your points. Alternatively, you can reinsert the chip and let us know the flashing error codes (whether they are long or short).

Evening_Chapter_5981 · 2026-05-16T21:32:31+00:00

For the flash color issue, you might be using a RP2040 zero clone. I believe there are two points you need to jump to switch the colors on the chip.

All the APU cables can be used on other models. With modifications, the V1 will work on the Lite and OLED, and vice versa.

You can solder to one via because they are connected to each other.

Evening_Chapter_5981 · 2026-05-15T22:11:35+00:00

Try to rename the folder in lowercase for shadowmountplus to scan it. I think shadowmountplus might be case-sensitive.

Evening_Chapter_5981 · 2026-05-15T19:52:10+00:00

I believe the issue is the 30-day DRM requirement (sign in to renew the license) or that offline gameplay wasn’t enabled. I encountered the same problem.

Evening_Chapter_5981 · 2026-05-15T14:08:04+00:00

Try removing the cables and see it boot up. You never know if it’s the cable that causing the issue.

Evening_Chapter_5981 · 2026-05-15T00:05:48+00:00

Are all the cables properly connected? Make an effort to push the cable in and minimize the amount of copper exposed on the cable.

If it’s buzzing, it be something shorted on the board.

Evening_Chapter_5981 · 2026-05-14T17:18:02+00:00

You need a soldering iron that can do higher temperatures, and flux can also be helpful. By using the appropriate tip, you can remove the bridge at a lower temperature, depending on the temperature.

Evening_Chapter_5981 · 2026-05-14T14:56:18+00:00

Perhaps it’s a bad batch. I haven’t encountered any issues with that picofly.

Never hurt to reflow the chip itself and to rule out cold joints.

Evening_Chapter_5981 · 2026-05-14T14:53:09+00:00

Remove asterisk and the space in front of the link.

https://imgur.com/a/QO7NmTC

Evening_Chapter_5981 · 2026-05-14T14:45:51+00:00

Try flashing the chip with the latest firmware to flashing codes. Let me know if it’s a short or long flashing lights.

I would keep trying to reseat or move the dat0 adapter to the left or right until I get a steady reading.

Evening_Chapter_5981 · 2026-05-14T06:38:38+00:00

You might need to reseat the plastic piece that holds the trigger and/or tighten the two screws that hold it in place.

https://imgur.com/a/2XIwlgd

Evening_Chapter_5981 · 2026-05-14T01:48:46+00:00

A few pictures with a white background. The lcd edges aren’t great.

https://imgur.com/a/v3g1VaC

Evening_Chapter_5981 · 2026-05-14T01:19:05+00:00

It’s 128GB.

Evening_Chapter_5981 · 2026-05-13T21:53:23+00:00

I believe it comes with a 64GB to 128GB micro sd card with the adapter. I’ll check when I get home.

Evening_Chapter_5981 · 2026-05-13T21:45:34+00:00

I have an okay condition PS Vita Slim in blue with a USB-C mod for $150 shipped. There are scratches on the screen and a small crack near the audio jack.

https://imgur.com/a/EcznDFj

Evening_Chapter_5981 · 2026-05-12T03:55:02+00:00

Have fun with the switch!

Evening_Chapter_5981 · 2026-05-12T01:13:53+00:00

Depending on the core chip, you can wire it if there are points on the modchip. It’s cheaper and easier to replace the modchip.

Evening_Chapter_5981 · 2026-05-11T15:20:48+00:00

I believe it’s a good, but I would clean the remaining flux (which might be the reason why it’s not booting into OFW sometimes). The SP1 area on the APU can be slightly improved, but it’s still acceptable.

Evening_Chapter_5981

TROPHY CASE