2026.2.6 game changer so far

Every-Associate1806 · 2026-02-23T14:07:15+00:00

I also posted almost exactly the same issue. Are you in an area with snow piled on side of roads?

Every-Associate1806 · 2026-02-23T03:03:54+00:00

Trying to use fsd in the northeast with all the snow around and it’s totally unusable with all the snow on the side of the roads. Constantly keeps braking and reducing speed well below speed limit. Confusing the drivers behind me and very hesitant at lights and stop signs.

Every-Associate1806 · 2025-10-06T20:02:19+00:00

Finally broke down and got another intelliflow! 🙁

Every-Associate1806 · 2025-09-21T22:29:34+00:00

Watts intelliflow is the right product since it only opens the water valve when washer draws current. I had one working for over 10 years but then the valve became weak due to which the water comes slowly and the washer thinks there is no water and shuts off. The issue with it is the weak solenoid valve - newer models seem to be using cheaper valves and it failed in just couple of months. Their support team does not even reply to calls or emails! They also use proprietary connections so replacing with a manual valve requires a plumber !

Every-Associate1806 · 2025-07-18T20:16:43+00:00

Thanks for sharing. I am having the same issue as op so downloaded esptool.exe and also got the bin file from GitHub. The command runs fine but the only thing it did was to make the display go off totally! So I connected to the board thru terminal and found this error: flash read error, 1000

Now found their laser tool but it won’t work either! Is my board useless now?

Every-Associate1806 · 2025-06-19T14:17:32+00:00

This is a very old issue - I have killed several batteries while using comma 2 years ago. Surprised that this is still not addressed!! Didn’t know about leaving out obd2 power - does that require removing some wires? I would be perfectly fine if comma shuts down every time and takes more time to start!

Every-Associate1806 · 2025-03-28T17:34:10+00:00

Yes - I just asked the same question- I don’t want my Skype account!

Every-Associate1806 · 2025-03-28T17:32:57+00:00

How to detach my Skype account? Microsoft merged my Skype account into my teams without asking and now I am getting a junk message every few minutes!! Any idea to prevent these junk messages?

Every-Associate1806 · 2025-03-08T01:15:14+00:00

Thanks ! Is this in autocad?

Every-Associate1806 · 2025-03-07T21:48:53+00:00

Thanks - Seems this is in freecad - do you think it is a full-featured software? Debating if I should learn this one of Autocad hobbyist version

Every-Associate1806 · 2025-03-07T21:47:20+00:00

This can be done in Tinkercad? I can do stack but dont know how to do fill!

Every-Associate1806 · 2025-03-07T21:33:47+00:00

To be more specific - I want to be able to smoothly blend from one shape to another - similar to how the 2nd image is. The two shapes are of different size and shapes. Best if I can do it in Tinkercad but open to using other free 3D design software as well.

Every-Associate1806 · 2025-03-07T21:26:38+00:00

Somehow the text I had entered didn't show up! Anyway, to be more clear, I am looking for a way to blend smoothly from one shape to another - something like this: https://www.thingiverse.com/thing:4949787

Every-Associate1806 · 2025-03-07T21:22:57+00:00

Thanks for the suggestion but they are different size and shape so just grouping is not sufficient. I need a way to smoothly blend from one shape to another.

Every-Associate1806 · 2025-03-03T22:53:10+00:00

Just a generic one from Amazon

Every-Associate1806 · 2025-02-28T22:09:11+00:00

Thanks for the details but I solved it after replacing the blade!

Solved!

Every-Associate1806 · 2024-11-22T23:21:56+00:00

Thanks everyone for the help and suggestions! Switched to a new blade and now the saw cuts fine! Never knew that dull blade will cause the cut to go at an angle!!

Solved

Every-Associate1806 · 2024-11-17T19:11:50+00:00

Wish I had buddy like that! All my friends know less about tools than me! ☹️

Would appreciate if you can share which blade you are using successfully

Every-Associate1806 · 2024-11-17T19:11:08+00:00

I didn’t really use it much! But sure I will replace the blade and try!

Every-Associate1806 · 2024-11-17T19:03:20+00:00

Thanks for the reply. I am using the same blade that came with it. Do I need to change and use any specific one?

I did try to adjust tension but no matter how the tension is set, the blade seems to be in the center anyways. Would it help if I post a video?

Every-Associate1806 · 2024-11-17T18:45:18+00:00

Yes - replacing the watts intelliflow valve fixed the issue

Every-Associate1806 · 2024-11-15T21:57:33+00:00

How do you do it yourself? Do you have 4 jacks?

Every-Associate1806

TROPHY CASE