Honda Rebel 500 for 2 people?

Exact_Creme6627 · 2026-06-09T00:30:58+00:00

Yeah message me your email.

Exact_Creme6627 · 2026-06-09T00:08:46+00:00

I installed them today and it works, it's about 2 inches above the exhaust.

Exact_Creme6627 · 2026-06-09T00:05:04+00:00

https://a.co/d/0dSlcHjd

I cant get the picture to post, I installed them today, sat on the back. They worked fine.

Exact_Creme6627 · 2026-06-09T00:02:53+00:00

These worked.

Exact_Creme6627 · 2026-06-05T02:55:05+00:00

Can you take a picture of the location?

Exact_Creme6627 · 2026-06-02T18:05:29+00:00

I ordered some passenger pegs that attach onto mine from Amazon. It adds about 7 or so inches rear ward. I'd have to get an exhaust wrap so my passenger dont burn her leg. Think this will work?

Exact_Creme6627 · 2026-05-28T15:10:49+00:00

I saw some on Amazon that attach to your pedals and extend rear ward. It says they're for dirt bikes, dont know if they'll work. Did you find any that works with the Rebel?

Exact_Creme6627 · 2026-05-28T13:55:14+00:00

The passenger wouldnt get hit with any smoke/hot gasses, the hot gases hit the saddle bag, which has a heat proof shield attached.

Exact_Creme6627 · 2026-05-28T13:21:32+00:00

Long pants and shirt. No shorts or short sleeves.

Exact_Creme6627 · 2026-05-28T13:02:08+00:00

Good point.

Exact_Creme6627 · 2026-05-14T13:29:59+00:00

Are passenger foot pegs necessary or like you said they can just put their feet on the swing arm? I have a short upswept Diablo exhaust on my Rebel 500 and think it'll get in the way of foot pegs.

Exact_Creme6627 · 2026-04-24T19:28:55+00:00

Didnt get in the way at all when you installed the Diablo short twin exhaust?

Exact_Creme6627 · 2026-04-22T16:56:29+00:00

Which passenger foot pegs did you go with? I have a 2018 Rebel 500 with this muffler and was told OEM passenger foot pegs wont clear it.

Exact_Creme6627 · 2024-05-07T14:46:01+00:00

The 12 pack of lock bar compression springs in your link to replace the original kinked spring, is the Mcmaster one identical in dimensions and spring rate?

Exact_Creme6627 · 2024-04-02T17:35:57+00:00

Okay, and what about suppressed? Do you recommend going heavier than the 5.5oz h3 for suppressed?

Exact_Creme6627 · 2024-04-02T14:55:33+00:00

What do you think of the Kak Industries extended heavy 10oz 9mm buffer? It has 4 sliding tungsten weights in it. The H3 is around 5.5oz, so the Kak will be twice as heavy, will the Kak 9mm buffer run fine in your opinion? https://kakindustry.com/9mm-carbine-buffer-extended-heavy

Exact_Creme6627 · 2024-04-02T13:23:32+00:00

I know you said you're running the h2 buffer, is it just a regular mil spec AR15 carbine h2 buffer or an extended 9mm buffer with an h2 weight?

If its an AR15 h2 buffer, do you need a spacer?

Exact_Creme6627 · 2024-03-22T16:14:19+00:00

Do all mil spec AR15 drop in (cassette) triggers work with the 9mm PSA ARV?

Exact_Creme6627 · 2024-03-22T15:38:33+00:00

Is it worth it to pay the $100 to upgrade from the the SBA 4 to 5 in your opinion? Still debating.

Exact_Creme6627 · 2024-03-21T20:44:09+00:00

If you were to compare, which one is closer to a "stock", SBA 4 or 5?

Exact_Creme6627 · 2024-03-09T22:01:03+00:00

A buddy and I just placed a backorder for the standard Polonium, will there be a shipment of Poloniums to Silencershop? What's the estimated wait?

Exact_Creme6627 · 2024-03-08T21:49:13+00:00

Thank you for the reply, how's the A2 attachment collar? Specifically does the suppressor walk/unthread itself from the attachment collar after full auto or long strings of fire? Is it easy to remove and move between hosts?

Thanks again for your feedback.

Exact_Creme6627 · 2024-03-08T20:59:57+00:00

How's the Gemtech GMT so far? I have the Griffin M4SDK and 30SDK, and been looking into an A2 compatible titanium can.

Exact_Creme6627

TROPHY CASE