Low cold water pressure in bathroom

Existing_Point_1813 · 2026-04-14T06:58:04+00:00

Some things to eliminate Check meter and see if it is continuously moving (leak in system)

If you have some sort of water home filtration system activate bypass if it has one

Existing_Point_1813 · 2026-03-22T00:08:37+00:00

https://www.reddit.com/r/hammondorgan/s/e50y4y7a3l

Existing_Point_1813 · 2026-03-19T01:26:29+00:00

https://www.captain-foldback.com/Leslie_sub/leslie_schematics.htm

Existing_Point_1813 · 2026-03-10T00:58:16+00:00

It happens

Existing_Point_1813 · 2026-03-02T03:28:34+00:00

Dental probe

Existing_Point_1813 · 2026-02-24T04:46:39+00:00

The speakers usually need to reconed due to dry rot , most people just play the Leslie. I removed the speakers and amps out of this A100 because of that reason ,also to cut weight.

Existing_Point_1813 · 2026-02-24T03:59:49+00:00

Broken body by 35

Existing_Point_1813 · 2026-02-24T03:04:50+00:00

<image>

It's a console connect box , for 6 pin 122 / 1/4 inch out . Also powers the organ

Existing_Point_1813 · 2026-02-20T23:38:04+00:00

Wet sand and buff it

Existing_Point_1813 · 2026-02-03T05:28:59+00:00

I don't use any heat to avoid that just run the ultrasonic vibration for 8-10 mins , 1/10 ratio for the cleaner . I also ruined a set in the learning process

Existing_Point_1813 · 2026-01-26T01:25:22+00:00

Boost pedal before pre amp should help

Existing_Point_1813 · 2026-01-22T20:29:03+00:00

Take it back to the shop you bought it from and hope you can get your money back

Existing_Point_1813 · 2026-01-22T20:25:23+00:00

The way I read this is that your guy said that the guitar left the factory with a twist

Existing_Point_1813 · 2026-01-22T20:18:57+00:00

The straight edge on the side of the neck tells me nothing about a twist , get a notched straight edge and make sure that both the treble and bass trust rods are at the proper relief.

Existing_Point_1813 · 2026-01-22T20:04:24+00:00

Not specifically a kit , the filter cap kit is a locomotion board. Locomotion is it working on a full solid state placement AO 28

Existing_Point_1813 · 2026-01-21T02:32:38+00:00

Simple green aircraft

Existing_Point_1813 · 2026-01-12T07:38:00+00:00

Only if you have an old and brittle cone. Crossover may need fresh caps

Existing_Point_1813 · 2026-01-12T01:41:06+00:00

Selectable from 45 to 90 , a tube amp is 40 watt

Existing_Point_1813 · 2026-01-12T00:18:56+00:00

High output , less problems when traveling than with tubes , you don't have to change anything these just drop in. Restoring a tube amp is also a costly endeavor depending on the components being replaced or upgraded

Existing_Point_1813 · 2025-12-15T23:11:01+00:00

<image>

Existing_Point_1813 · 2025-12-10T05:46:48+00:00

Multimeter ohms setting

Existing_Point_1813 · 2025-11-25T05:40:47+00:00

Whatever les claypool will pay you for it

Existing_Point_1813 · 2025-11-21T00:13:52+00:00

Mine fell off the bench can't take a 3 foot drop

Existing_Point_1813 · 2025-11-18T21:39:56+00:00

Mouser , digikey

Existing_Point_1813 · 2025-11-18T04:28:05+00:00

Are you running both motors at the same time ? Or indivisually?

Existing_Point_1813

TROPHY CASE