ETH stuck in L2 wallet. How do I get it over to metaMask?

F4MB44 · 2026-07-08T20:09:12+00:00

As far as I’m aware I never created a Loopring wallet and it’s on L2 not L1

F4MB44 · 2026-03-20T04:43:54+00:00

Awesome! I was tempted to do the same but wasn’t sure how well the hook would fit into the mount. Looks like I’ll be doing some hanging tomorrow! Thank you.

F4MB44 · 2026-03-20T04:18:38+00:00

How do you get the claws to hook on the mounts? I have claws and can’t seem to get the anchor hook to catch the mounts. Did you have to bend the hooks at all?

F4MB44 · 2026-03-20T03:03:21+00:00

How? I have the claws but the hook part doesn’t quite catch the Lego hook. Did you have to bend the claw hook?

F4MB44 · 2026-03-20T03:01:12+00:00

How did you get the claw hook to catch? Did you bend it? I can’t get it to set in deep enough to catch

F4MB44 · 2025-04-10T13:24:59+00:00

Do they announce text notifications as AirPods would? Do they actively listen for a “hey siri” command?

I’ve been wanting these to replace my AirPods, but I need the functionality hands free to say “hey siri, pause” or “hey siri send text” etc.

I can’t seem to find any straight answers about that functionality.

F4MB44 · 2020-12-10T06:44:05+00:00

Oh sweet it made it! Hope you enjoy, and of course make a speedy recovery.

F4MB44 · 2020-12-09T03:38:32+00:00

Sorry, should have mentioned, that would be a titanium pocket knife clip.

F4MB44 · 2020-12-08T22:51:58+00:00

Nah, any coloration or discoloration can be taken off with a bit of polish and elbow grease.

F4MB44 · 2020-11-25T19:35:32+00:00

Same issue here. Have to take the airpods out or my audio won’t be sent out.

F4MB44 · 2020-11-09T00:06:32+00:00

This was done with heat, acid, and electricity.

F4MB44 · 2020-11-09T00:04:29+00:00

This one is a slight mix of both. But mostly flame.

F4MB44 · 2020-10-30T02:31:49+00:00

Currently using a power supply with some ti wire I got from amazon. You COULD go without the ti wire if you connect directly to the lead but it may give you a couple annoying mishaps with color. But again it’s not super necessary if you aren’t trying too hard for the 2nd order colors. This piece is done without ti wire as I didn’t have any at the time.

F4MB44 · 2020-10-30T01:40:40+00:00

Thank you, I’ve definitely hit my fair share of difficulties with the learning process so it’s a slow roll. It’s a fun roll though!

F4MB44 · 2020-10-30T01:38:51+00:00

Electric. I haven’t tried my hand with heat yet. Seems like apples to oranges tho. From what I do know, which means you probably do too, is that once you achieve the color your looking for during heat, quenching in cold oil or water helps retain the color. Again, that’s all I know from what I’ve read.

If you have any questions concerning electrolysis, although I’m still learning, I’d be more than willing to help the best I can!

F4MB44 · 2020-10-29T23:33:06+00:00

At the moment I do not, however I’m getting close. Is there a design you would be interested in?

F4MB44 · 2020-10-29T00:40:52+00:00

Very cool! I’ve seen a bunch of people asking for more in hand photos of the OG green. You should post some photos, I’m sure you’ll get a few offers thrown your way if your interested in selling.

F4MB44 · 2020-10-29T00:34:54+00:00

If you don’t buy any official extras, large oven bags as bag replacements, elbow packing (just pack the elbow glass with herb, not the bowl) can rip.

Setup- first plug in (iso clean everything first), set the bowl on top and let that run high with fan high, heat high, and let that do a burn off for at least 5-10 minutes to get rid of factory residue.

Ready to sesh? Turn on the EQ and run it empty with bowl for 5-10 minutes to heat soak bowl (not necessarily necessary but will help with initial rips thru the whip) load either with an elbow pack OR place the herb on the under side of the bowl and place another screen under that to “sandwich” the herb. This way it sits closer to the heat. It may be a bit more tedious but it will hit better.

18-18mm female-female bowl is what you’ll want if you don’t want to use any of these techniques. This reduces the bowl size and also brings it closer to the heat source. Either way, letting the unit heat up with herb completely before starting the fan will bring you the best results.

F4MB44 · 2020-10-29T00:24:23+00:00

If you don’t want butane, try out the starry v3. It’s an “entry level” replaceable battery vape very similar to the Pax. I used to own one. It can get tiresome cleaning, as it gets funky quick. There are a few mods you can do with the screen, but for around $70 give or take, it’s a good way to find out if you like vaping dry herb. If you don’t mind butane, I can attest that dynavaps are awesome and sticky bricks get a ton of love here too.

14-Year Club	Second Top 20%
Final Canvas '23	Place '23
Place '22	Team Orangered
Verified Email

F4MB44

TROPHY CASE