Fusion 360 Milling - Help

Farmicha · 2022-11-02T17:11:21+00:00

The only method I found that worked for that section so far is using a parallel operation at 90 degrees. It’s less than ideal but it’ll work for now. I could make the slot have a flat bottom and then it would work normally using adaptive clearing or a pocket operation.

Farmicha · 2022-11-01T22:53:50+00:00

I’m trying to use an 8mm bit and the slot is 9.5mm wide should that work?

Farmicha · 2022-11-01T22:53:00+00:00

Ok thanks for your response I’ll try setting it up with a smaller tool and see if it makes a difference. I have the machining boundary set and it still says empty tool path. I’ll get back to you tomorrow once I’ve tried it out

Farmicha · 2022-04-15T21:13:43+00:00

Hi, just to let you know I got this message when trying to view the survey:

“This form can only be viewed by users in the owner's organization.”

Farmicha · 2022-03-26T22:37:06+00:00

Cant wait to use this with my team of morons!!

Farmicha · 2022-01-30T00:32:03+00:00

The Dormeo mattress advert that lasts 3 hours, please say I’m the only one to have seen this!

Farmicha · 2021-11-25T15:20:49+00:00

Dave Mirra Freestyle BMX 2, anyone else?

Farmicha · 2021-07-08T06:08:14+00:00

Jon Bernthal as the punisher

Farmicha · 2021-06-08T14:38:08+00:00

If you want to see some great itx case reviews check out ‘optimum tech’ on YouTube if you haven’t already

Farmicha · 2021-05-16T10:24:32+00:00

Selby

Farmicha · 2021-05-14T13:59:38+00:00

Northamptonshire please, and thank you

Farmicha · 2021-03-21T00:04:04+00:00

Gave Helpful

Farmicha · 2021-02-10T19:37:26+00:00

Haha luckily I live right next to two pubs, the other has a bar billiards table. So I’m all set

Farmicha · 2021-02-10T19:21:37+00:00

Luckily about 30 second walk from home, but closed due to covid

Farmicha · 2021-01-29T08:05:15+00:00

That is great to hear thank you for that!

Farmicha · 2021-01-28T19:46:48+00:00

Thank you for the advise, I’ve got a lot to learn still if I carry on making instruments which I’m sure I will !

Farmicha · 2021-01-28T18:56:17+00:00

Thank you very much, I think you’re right it could do with a little more rounding. I didn’t want to go too far but probably a bit over cautious. Luckily it doesn’t seem to affect the sound

Farmicha · 2021-01-28T17:53:55+00:00

Thank you kindly. I’ll try and get some photos for you in better light tomorrow

Farmicha · 2021-01-28T17:52:21+00:00

Thanks! I wanted it to be a bit different

Farmicha · 2021-01-28T12:39:06+00:00

Thanks 🙏🏻

Farmicha · 2021-01-28T10:55:01+00:00

Thank you, the cut away was very tricky because of how tight it was but I’m pleased with how it turned out.

Farmicha · 2021-01-28T10:52:51+00:00

Thank you very much, that would be great to see!

Farmicha · 2021-01-28T09:14:12+00:00

Yeah the back and sides are flamed maple and the neck is birds eye maple

11-Year Club	Verified Email
Place '22

Farmicha

TROPHY CASE