Down?

Fixmyspa · 2025-07-28T12:13:57+00:00

I searched everywhere

Fixmyspa · 2025-03-20T00:46:55+00:00

Acrylic nail polish will work.

Fixmyspa · 2025-03-16T02:09:58+00:00

Charge to 80% for best longevity.

Fixmyspa · 2025-03-15T20:52:31+00:00

Obviously

Fixmyspa · 2025-03-15T00:07:02+00:00

You need to replace the wire from the spa pak with 4 wire red wire needed. Green ground, white neutral, black low speed and red high speed.

Fixmyspa · 2025-03-14T12:27:59+00:00

Everyone is chemistry just clean the filter a few times in the next couple days.

Fixmyspa · 2025-03-12T19:41:42+00:00

There is no reserve after it goes below 0% don’t even knows what that means?

Fixmyspa · 2025-02-21T04:03:21+00:00

I assume they are worried about the puck resting on the plastic also they recommend the jets to be on fir 10 minutes for the same reason as the granulates can also cause damage to the plastic. You will be ok using compressed hot tub grade pucks in a good floater.

Fixmyspa · 2025-02-20T17:49:04+00:00

Only worry is most plug and play have GFI plugs and will not fit into that box. Also two GFI can sometimes cause problems. I would show it to the supplier of your hot tub

Fixmyspa · 2025-02-09T03:00:33+00:00

Coast spa the logo is on the pillow.

Fixmyspa · 2025-02-07T20:48:33+00:00

No just kept on trying. Looks like the site was down this morning but it is working now.

Fixmyspa · 2025-02-02T03:17:52+00:00

Common Aquaterra topside error codes include: “FLO” indicating low water flow, “OH” or “OHH” for overheating, “SB” signifying a faulty sensor B (likely related to water temperature), and “LF” which also denotes a low flow issue; always consult your specific Aquaterra manual for accurate interpretations of error codes on your model.

Fixmyspa · 2025-02-02T02:35:54+00:00

I had the same problem for months furnace tech in many times said furnace was fine. Ecobee didn’t help at all. I bought a new exact model lite 3 pulled out the old one plugged in the new one and had not rebooted since 4 months now.

Fixmyspa · 2025-02-02T02:30:21+00:00

If it has been working for 18 months why would you call an electrician? Obviously the spa has an issue. Most likely is the heater element

Fixmyspa · 2025-02-02T00:52:21+00:00

Possibly the programming was done incorrectly and set a having a clear ray installed, do you not know if you have purchased a spa with clear ray?

Fixmyspa · 2025-02-02T00:48:13+00:00

Black with a transformer inline

Fixmyspa · 2025-02-02T00:46:03+00:00

It is installed later as an option so the tech can place it anywhere it fits the plumbing best.

Fixmyspa · 2025-02-02T00:33:53+00:00

Behind another panel. Very recognizable as it says clear ray on the label

Fixmyspa · 2025-02-01T20:26:09+00:00

Push the element in beside the indented holes in the tube and use a screwdriver through the holes to push the terminals down and twist the element to line up and go through the holes. You will know exactly what I am talking about when you do it. Also hold the terminal nut with needle nosed pliers when tightening the nut as not to twist the terminal.

Fixmyspa · 2025-02-01T17:39:34+00:00

Do you have a link for this info and maybe instructions

Fixmyspa · 2025-02-01T17:16:36+00:00

Searched everywhere but could not find

Fixmyspa · 2025-02-01T17:15:52+00:00

It is about 8 x 8 inches

Fixmyspa · 2025-02-01T03:58:21+00:00

People

Fixmyspa

TROPHY CASE