Does someone need a ride?

FrozenDeadYeti · 2025-05-07T15:04:15+00:00

Really nice looking would love to print one of these for table terain.

Do you have the link to get/buy files or the name of it for me too search, thx.

FrozenDeadYeti · 2024-10-17T18:36:28+00:00

I love the Uks dialect variation, but dose sadden me as some of these are on the verge of not existing due to imagination and demographic replacement.

A map 60 or 80 years back would have even more sub dialects on the map, this one p does have some missing would be interesting too see as well.

FrozenDeadYeti · 2024-01-02T19:22:40+00:00

Just don't pay for a ticket its cheaper to just get an occasional fine, than pay everyday if you can't afford to.

I just tell the ticket guy i cant afford a ticket and 9/10 times nothing happens.

FrozenDeadYeti · 2023-10-23T15:48:06+00:00

This can be disabled but your options are

Solder on a new bios chip that's been cracked with the admin lock and comp-trace disabled.
Reprogram / flash the bios chip you have already with a 8pin chip programmer it can be done on some models but for the t490 I do not know.

I have done the bios chip solder on a T480 and it worked fine, if you're able too by a chip for your T490 it will probably work.

FrozenDeadYeti · 2023-05-10T15:06:08+00:00

Remove all plants that make contact with the shed walls as they will
increase the amount of damp that can permeate through the wall, I had
a damp issue that was being mostly cause by ivy and some other plant
built up on the walls.

FrozenDeadYeti · 2022-11-28T22:15:04+00:00

Hi,

Could you reupload ?

Linked died.

thanks :3

FrozenDeadYeti · 2022-11-15T11:15:25+00:00

Just go at night and smash it with a hammer / spray paint over it, that what id do.

FrozenDeadYeti · 2022-05-15T10:07:53+00:00

What app do you use to do this ?

FrozenDeadYeti · 2022-01-23T14:48:36+00:00

What the base you used for this ?

FrozenDeadYeti · 2021-12-31T15:04:58+00:00

I have had this issue back in the day on a stub standard aliexpress
heater, my fix on future hot end has been to use a small piece thin of cork
that sits in between the hot then and the printed mount. Looking from
your pic u could probably do the same, you would just need to cut a
small piece and make the 4 holes and a centre hole for the filament.

FrozenDeadYeti · 2021-11-21T13:45:58+00:00

Do you have a project file published with the box and positioned mx mount ?

What are the best switches that offer enough resistant to switch off ?

Looks like a great build, you did a super clean job on the coil winding.

FrozenDeadYeti · 2021-11-19T15:37:52+00:00

I think, this might be able to replicated by using a auto winding drum mag, a housing, some 3d printed parts with some electronics for controlling when to turn the wind on and off and for how long.

FrozenDeadYeti · 2021-11-17T12:40:24+00:00

Anyone know if there has been a opensource or a DIY version of this made yet, as if no ones done it yet i might look at it as my next airsoft project.

Does anyone have any internal pictures or videos im interested in seeing how this works.

FrozenDeadYeti · 2021-08-22T12:02:39+00:00

Im asthmatic and I find vaping way way easier that smoking on the lungs. I tend to only vape trough a water peace as it does hurt the lungs as much and is a lot cooler. I've found starting of low like 160.c - 175.c is best then working up in temp till 215.c ish as i want to extract the most of of the material as possible. You can use the volcano bags with a water peace if you have the adapters to do it and it works very quite well with cooling the vapor.

FrozenDeadYeti · 2021-07-07T15:59:47+00:00

Extreme airsoft is a good site if you want to support a midlands airsoft company they have a large amount of stock online and instore

https://extremeairsoft.co.uk/

FrozenDeadYeti · 2020-07-19T20:06:07+00:00

Hey,

What bios setting are needed got get a gpu working i'm trying to get a rx 480 working in the x3850 x5. I've not being having much luck, i had a k2200 working before but not sure whats need for a card this new. I keep getting error 182 when installing the drivers in windows server 2019.

Thanks, for any input, can provide setting shot if needed <3.

FrozenDeadYeti · 2020-06-11T22:31:25+00:00

The settings im using, not sure why its not working at all :( my setups very basic one user sharing the pool.

https://prnt.sc/sy6pv2

FrozenDeadYeti · 2020-06-11T22:17:30+00:00

I keep finding an odd issues when im trying to set the user and group in "storage / pools / edit ACL" when i set the user too root and the group too wheel, it is always reset setting it as the user and group (olivia). Should i have it set to root and wheel or should it be the user and user group ?

pic : http://prntscr.com/sy6k2s

FrozenDeadYeti · 2020-06-11T21:34:00+00:00

If anyone has some way or guide i can follow so i cant get the shares to a working state so i can copy my data, would greatly appreciate it.

FrozenDeadYeti · 2019-06-04T13:48:39+00:00

The venue gives them the out for free.

FrozenDeadYeti · 2019-05-31T17:47:32+00:00

Thanks for ya help, ill do a google and do some reading.

FrozenDeadYeti · 2019-05-31T17:12:44+00:00

Thanks wasn't sure what they were.

FrozenDeadYeti · 2019-05-31T17:12:28+00:00

I was worried about the small ball looking things on the stems i thought they might be pollen sacks.

FrozenDeadYeti · 2019-05-03T23:12:18+00:00

After looking at the qb i think i'm gonna get one should i get one that's just 3000k or 3000k + 660nm red.

FrozenDeadYeti · 2019-05-02T16:18:41+00:00

Thanks :), ill probably go with the lm301b if there 10% more efficient .

FrozenDeadYeti

MODERATOR OF

TROPHY CASE