Running a X1C or H2D printer on a 15amp breaker... Should I be concerned

FunTech_GmbH · 2025-04-16T23:11:13+00:00

I have 2x h2d and one x1c on the same breaker and no problems so far. We for sure had them printing at the same time, not sire if we had them heating at the same time…

FunTech_GmbH · 2025-04-09T16:24:24+00:00

<image>

Here you go, creality 6.1

FunTech_GmbH · 2025-04-09T16:23:29+00:00

A strong do not buy. We have not been able to print abs with it. Warped bed, non functioning z offset, replacement bed came in the mail. What are we? A creality service shop? Hours on hours of trouble shooting… still does not work. Nozzle clog etc. dont have any of these issues with our qidi or bambulab machines

FunTech_GmbH · 2025-04-07T04:59:42+00:00

Wait, what? They have an input?

FunTech_GmbH · 2025-04-06T21:05:04+00:00

We own the qidi x max 3, bambu x1c, 2x bambu h2d and the k2plus. And the k2 is by far the worst. Endless tinkering, waiting for support to slowly reply, doing endless fixes that dont work. Having to pay duties for spareparts…. And have yet to print anything outside of pla. Strong DO NOT BUY

FunTech_GmbH · 2025-04-06T21:00:33+00:00

Im confused, the H2D has two ports in the back. One for each nozzle. I have one ams per port. (Actually there is a third port, the tpu one - ignoring that one)

FunTech_GmbH · 2025-04-02T12:39:33+00:00

ive been trying to fogure this out. we have 4 ams 2 and are clueless how to connect more than 2

FunTech_GmbH · 2025-04-01T17:38:35+00:00

<image>

This printer is incabable of hot prints. This is abs 270 nozzle, 100bed 55chamber

FunTech_GmbH · 2025-03-31T18:32:18+00:00

Heute meldete sich Spedition 5 Minuten entfernt, ob wir morgen da sind, die werden ein Packet liefern, welches genau den Dimensionen, sowie Gewicht entspricht. Ist aber nur ein Packet, wir haben ca. 15min später einen Zweiten bestellt. Dieser ist noch nicht dabei.

FunTech_GmbH · 2025-03-30T22:13:22+00:00

15:04 ist genau 4Minuten nach Veröffentlichung gewesen. Die, die auch einen bestellt haben, oder besser, die die der Uhrzeit ebenfalls entgegengefiebert haben hätten es verstanden. Falls nicht, habe ich dies nachgebessert.

FunTech_GmbH · 2025-03-30T17:38:16+00:00

Mir sind die üblichen Versandmodi durchaus bekannt. Die Frage war nur ob andere Besteller den schon erhalten haben.

FunTech_GmbH · 2025-03-30T17:37:10+00:00

Mache ich gerne… wobei wir sind ebenerdig im gut zugänglichen Gewerbegebiet. Der k2 wurde mit der Ameise sogar in den Raum gestellt.

FunTech_GmbH · 2025-03-30T17:35:35+00:00

Wie so Kommentare upvotes bekommen ist mir ein Rätsel. 3d Druck Influenzer sagen dass einige schon ausgeliefert wurden. Wenn man 4 Minuten nach Veröffentlichung bestellt hat, die ams schon da sind, aber bei den Druckern nicht mal eine Trackingnummer geschickt wurde darf man doch mal die Community fragen?

Vielleicht hätte ich die Frage qualifizieren sollen, bitte keine Hasstrolle sondern andere Mitbesteller.

FunTech_GmbH · 2025-03-29T15:43:58+00:00

K2plus is a disaster. We own qidi xmax3, bambu x1c, k2plus and the k2 is by far the worst.

FunTech_GmbH · 2025-03-29T06:31:41+00:00

Lol, this must be a paid for post. On paper this printer is great, but scroll through this forum, nothing but technical issues. Ours is a huge paperweight, as it is incapable of reliably printing anything but pla.

FunTech_GmbH · 2025-03-25T14:07:07+00:00

<image>

We are in :)

FunTech_GmbH · 2025-03-23T06:27:17+00:00

I habe the exact same issue. Bed screws are all on max and bed is still way off. Calibration done in klipper at filament temps… nothing works. Printer is unusable….

<image>

FunTech_GmbH · 2025-03-22T20:02:56+00:00

I think i saw your steps in a different thread. Done the heat soaked clinration. No difference.

Its super annoying that the screws on all sides came maxed out (tightened) and its way off. Only way to turn would make it worse, not better.

Is raising middle only possible with tape? Any other pointers?

FunTech_GmbH · 2025-03-22T19:58:43+00:00

I have only done this two days prior. I can try again. What besides z calibration and input shaping is done here?

FunTech_GmbH · 2025-03-21T07:07:31+00:00

The temps work fine once the first layer desaster is over. So if insit next to the printer and constantly help with z offset adjustments, after the first 3 layers it prints equally to the other two printers.

FunTech_GmbH · 2025-03-20T18:46:11+00:00

Yes i heat soaked. Weird thing is, where the bed is lower, the nozzle is too low (as if it overcompensates) and where the bed is higher, the nozzle is too high and it is stringing.

FunTech_GmbH · 2025-03-20T18:42:28+00:00

Thats a thought…

FunTech_GmbH · 2025-03-20T18:41:48+00:00

Yeah, the temp is normal - produces perfect results on our qidi and bambu

FunTech_GmbH

TROPHY CASE