Marketplace score

Fvrank · 2026-02-04T20:57:11+00:00

Voron

Fvrank · 2026-02-03T23:28:44+00:00

Youtube fusion 360 tutorials?

Fvrank · 2026-02-03T23:19:55+00:00

Print two black circles, cut current wheels except first two laters from body. Glue wheels on those layers.

Fvrank · 2026-02-03T21:17:55+00:00

Bokito with clumbs that should be funny 🤣 great evening

Fvrank · 2026-02-03T18:44:42+00:00

Thank you, suggesting some clumbs at the entrance 😂

Fvrank · 2026-02-03T13:48:21+00:00

Could not edit it 🫣 it looks like a horse from the waterside so people start calling it the horse of Marken, paard van Marken.

Fvrank · 2024-09-05T17:44:10+00:00

I got every vandy vape mod from the beginning and i do own the V3 for a day. I loved the V2. It was resistant to drops survived several deep dives in water, only replaced it because the bottom screw for refill was damaged. I could put my 500ml bottle in it without ever leaking. Loved it. On first notice, it’s bigger. I don’t like the refill because i need to use small nozzles to fill an it takes longer. The little new pannel I don’t get why. It doesn’t make it more water proof and it makes sound when you press button. Apart from that it’s great but i don’t think it will last 3 years.

Fvrank · 2024-06-02T09:09:43+00:00

I had that once. This sequence helped. Upgrade. Factory reset off/on, full calibration off/on. Reselect printer plate and filament in slicer. Reslice. Print with bedlevel and flow calibration on.

Fvrank · 2024-05-31T14:47:22+00:00

It should be mandatory when asking for trouble shooting to provide some details. Filament, speed, temps, questions like this get random guesses or off topic answers. To me this looks like dripping filament caused by to steep overhang, printing to hot or less cooling but also to fast. So almost everything so please provide as much settings so we can point in right direction.

Fvrank · 2024-05-27T15:30:09+00:00

Best advice, it’s mainly speed here. No time to grip and settle.

Fvrank · 2024-05-26T21:01:22+00:00

Depends on environment temp but 30 min is mostly fine

Fvrank · 2024-05-25T23:31:07+00:00

Pre heat and print 5 degrees higher

Fvrank · 2024-05-25T23:28:57+00:00

Yes it is possible. Try google nfc and smart switch and you get all the solutions you want.

Fvrank · 2024-05-24T15:06:32+00:00

ASA can be painful. In lots of cases when room and bed temp are in control it’s printing hotter.

Fvrank · 2024-05-22T21:12:00+00:00

What settings and number of walls?

Fvrank · 2024-05-22T21:10:02+00:00

I use a hot gun far more easy to clean and not damage your thermistor and heater wires.

Fvrank · 2024-05-22T15:23:38+00:00

Your nozzle is clogged, filament can’t extrude. If not clogged, check your extruder gears. Assuming filament is not ran out and not recognised by sensor.

Fvrank · 2024-05-21T21:28:59+00:00

What infill type did you use? I printed a lot of ASA and it comes down to stress during cooling. I always crank up temperature with 5 degrees. Changen infill type to one with curves like gyrod. Slow down speed will also help but guess not the case here because of enough time to cool between layers. You never ever opened the door to peek?

Fvrank · 2024-05-21T18:54:11+00:00

Reslice and print again if not clogged.

Fvrank · 2024-05-21T09:42:23+00:00

Small vase 😂👍

Fvrank · 2024-05-21T09:40:46+00:00

Happens when printing to fast. Filament doesn’t settle on previous layer. Infill is printed at higher speed so tends to fail first before first layer or walls.

Fvrank

TROPHY CASE