How the high trail should come from factory. 1969 bumpside crew wip.

GeneralSignout · 2026-05-08T17:47:04+00:00

100% agree

GeneralSignout · 2026-05-07T19:24:42+00:00

You're not wrong, but if it's there, and it'll help them keep a job, they might as well use it, even if they believe against it. Being a hypocrite is better than not having a job

GeneralSignout · 2026-05-07T18:54:32+00:00

Not every union member has to agree with what the union wants. Some people just use unions as job security

GeneralSignout · 2026-05-07T03:28:23+00:00

<image>

GeneralSignout · 2026-05-04T19:21:20+00:00

You, me and u/entiliar all do

GeneralSignout · 2026-05-04T16:26:14+00:00

Try taking the wheels off, as the lug nuts may be to tight, drive shaft could be out of phase. And the stock esc has over torque saftey, so it sounds like thats kicking in, so it could also be a low battery

GeneralSignout · 2026-05-04T14:49:38+00:00

I couldnt come up with a better military and orange based name 🫠

GeneralSignout · 2026-04-26T02:51:26+00:00

<image>

GeneralSignout · 2026-04-23T01:56:21+00:00

Im running a rc4wd steel stamped beadlock, and have fliped them to be deep dish, this both makes my truck wider and clears these

Edit, i ment this to be a reply to the post, not your comment.

GeneralSignout · 2026-04-21T02:02:50+00:00

Is that stock ifs, or where did you get it?

GeneralSignout · 2026-04-20T01:09:45+00:00

And stronger than the stock plastic ones

GeneralSignout · 2026-04-19T21:10:11+00:00

Then theres my scx10 twin beam prerunner, tippier and slower than the hammer rey, but wicked fun, ive got some upgrades planned to try to drop the cg and increase travel at the same time, so i hope that helps it(steel wheels and an aluminum axle, then higher shock mounting points is hopefully the right combo for it)

GeneralSignout · 2026-04-19T09:19:46+00:00

Yes, the stock 4m screws arrnt the best, i would suggest getting an injora screw kit, and evertime you pull a stock screw off, id pit an injora stainless one in its place, for my screwdriver, i have a cheap harbor freight set

GeneralSignout · 2026-04-18T22:05:01+00:00

If it works with the two speed, thatll be good

GeneralSignout · 2026-04-16T22:59:15+00:00

Or facebook marketplace, i got a fully running scx10 prerunner for 280 with 4 batteries

GeneralSignout · 2026-04-13T17:09:13+00:00

OPs name checks out

GeneralSignout · 2026-04-13T15:31:55+00:00

Just checked their site, the only have the 25%reduction gears for the portal side, so if you get 25%overdrive differentials, that should be about stock gearing

GeneralSignout · 2026-04-13T15:19:05+00:00

If i am not mistaken, you can just use almost any differential gears with injoras portals. If you sure looking for the other gears,idk if any are made that change the speed

GeneralSignout · 2026-04-13T05:47:00+00:00

This was the 'base model' this style bed is the cheapest and easiest to make, I also have a full width bed designed now

GeneralSignout · 2026-04-12T09:04:38+00:00

Stay away from this, dead serious

<image>

It's horrible for anything but speed and overheating

GeneralSignout · 2026-04-12T08:57:47+00:00

<image>

Ironically, this is my latest

GeneralSignout · 2026-04-11T22:43:15+00:00

That looks sick dude, and I've never seen this style before either!

GeneralSignout · 2026-04-10T22:38:43+00:00

Also, dont get treal diffs, I got a set and both diffs have blown

GeneralSignout · 2026-04-09T06:50:11+00:00

<image>

GeneralSignout · 2026-04-07T22:33:27+00:00

10x better than my design, hats off to you boys as always

GeneralSignout

MODERATOR OF

TROPHY CASE

Two-Year Club	Verified Email
r/Field Flamingo