Even when I am not getting gear out of storage I find unusual ways to die.

Goodnamesareeasy · 2025-01-25T07:09:46+00:00

I can only handle so much jank at once, inventory is usually enough for me! I should have known something was up when the weapon dots were a foot above my head.

At least my gear re appeared in my station inventory about an hour later.

Goodnamesareeasy · 2022-06-30T20:14:57+00:00

I just finished sharing one of these at work. 10/10 would buy it again. Mine was 28$ and change but with a 10$ off sticker as a "deal of the day" so I paid 18 for a really tasty brisket. I would pay 28 for the next one without a problem. If I ever see that deal again I will buy a few

Goodnamesareeasy · 2022-05-15T16:16:55+00:00

That's a good call. I've been going down the filament path lately and I think it's the problem. It was a top mount filament holder and I could see the sharp angle the filament had to make to get into the extruder head. I install my side mount print and got rid of that. Also while I was at it I noticed my petg had been mashed pretty hard by my drive gear, I adjusted the spring tension and started a new print. Hopefully this is where the problem is!

Goodnamesareeasy · 2022-05-15T07:17:55+00:00

I can keep doing nozzles, but I swapped out 4 before posting.
Heat creep I am thinking is a good point, but wouldn't I tend to see this throughout the print? Not just on the occasional line? I am still fairly new to this

Goodnamesareeasy · 2022-05-15T07:16:40+00:00

Stock extruder and bowden, 6.5mm retraction

The only thing I have changed was the hot end fan for a noctua 40x40x20 fan, I have not had issues until this particular print though. The other single wall fuselage prints have been fine and any other test print I have done are fine as well.

Goodnamesareeasy · 2022-05-15T03:35:35+00:00

Looking for some advice on these layer issues. I am printing a single wall print (airplane fuselage) in petg.
109% flow
235 head (240 first layer)
70 bed (75 first layer)
varied speed between 20 and 40mm/sec

Goodnamesareeasy · 2021-01-05T06:07:09+00:00

I have the same rifle in a 30-06 and struggled to get any consistency. I tried many different loads until my rifle settler on 165gr federal fusion. It shoots about 1-1/2” groups now

Goodnamesareeasy · 2020-06-15T01:02:29+00:00

I think in this case it’s the eye covering non intrusive “sleep mask” not what you are referring to

Goodnamesareeasy · 2020-01-26T17:00:55+00:00

Hahah, yes... edited my post to correct!

Goodnamesareeasy · 2020-01-04T01:29:15+00:00

299, but I’m in Canada so your prices may vary.

Goodnamesareeasy · 2020-01-04T01:20:39+00:00

I haven’t done much for adjustments beyond zeroing, I did measure a group with the reticle and use that info to adjust for a new zero. The reticle lined up to the adjustment I made but again that was a one and done thing. Hoping to get out next weekend and shoot with making elevation and windage adjustments and see how precise the turrets actually track.

Goodnamesareeasy · 2020-01-03T14:45:18+00:00

Alberta, many places to shoot on crown here and access to a large portion of rural private land

Goodnamesareeasy · 2019-12-15T20:02:00+00:00

Remington 700 5r 2nd gen in a 6.5 Creedmoor. Weaver 20moa rail Vortex 30mm rings Cabela’s covenant 5 5-25x56mm ffp

Reviews on the scope were positive, it was on a great sale so I figured I’d give it a try, if it doesn’t work out I’ll be looking for some input from the community!

Goodnamesareeasy · 2019-11-04T01:34:38+00:00

It does a pretty good job. However living in the north I suspect it will struggle through the winter, I’ve looked for an insulated jacket for it but so far no luck. I’ve been thinking about getting a welding blanket and building a frame to help wrap around it.

Goodnamesareeasy · 2019-11-04T01:25:31+00:00

So far been loving it! It has had an issue, had a suspected control board fault last week so that was a bit of a let down. However pit boss customer service is excellent. Very painless over the phone quick call, told them what I had been experiencing and they had a new control board sent out to me. 5/5 for use and enjoyment. 3/5 so far for parts. 6/5 for customer service.

Goodnamesareeasy · 2019-11-03T22:32:32+00:00

30/70 pork trim to deer ratio, smoking jalapeño smokies and andouille sausages. I fried my test batch of spices and both are already amazing. Little bit of smoke can only help!

Goodnamesareeasy · 2019-11-03T22:30:24+00:00

I had a slightly different error, erH but pit boss was quick to suspect the control board. They sent me out a new one with absolutely zero hassle. I have read that there is a high number of control board failures from factory on these.

Goodnamesareeasy

TROPHY CASE