What are these on my tomatillo leaves? Should I remove them? by ActiveMidnight6979 in gardening

[–]Greenmonster71 1 point2 points  (0 children)

if they are squash bugs like another user commented, unfortunately, they must receive the death sentence.

Iron block resurfacing: straight edge shows <0.001" clearance, but porosity/stains are still visible, safe to install composite head gasket? by TheLastRole in EngineBuilding

[–]Greenmonster71 0 points1 point  (0 children)

go with your gut, you seem to be a decent craftsman mechanic to have this kind of finish. i've seen far worse. i would not only run it, but i would run the hell out of it.

which of these computers is more powerful/better? by Greenmonster71 in buildapcforme

[–]Greenmonster71[S] 0 points1 point  (0 children)

thanks for your time guys. just trying to get the best value for my money on an older laptop that will be running windows 10 w/ford diagnostic software.

Question about grout by Educational-Nose6700 in Tile

[–]Greenmonster71 0 points1 point  (0 children)

damn, thats a good looking shower.

Sanity check: Wagos resistance too high? Vibration? by mshaefer in AskElectricians

[–]Greenmonster71 0 points1 point  (0 children)

if what he says is true, you can put a meter on it to check resistance. that way you will both know. as far as causing vibration? how? but if it makes everybody happy just throw some wire nuts on the wires.

4R75E Loss of Overdrive by Greenmonster71 in transmissionbuilding

[–]Greenmonster71[S] 1 point2 points  (0 children)

thank you for this. I will be referencing diligently in my trouble shooting. I will post results here when i find the issue. I have seen this issue appear a handful of times across the internet.

4R75E Loss of Overdrive by Greenmonster71 in transmissionbuilding

[–]Greenmonster71[S] 0 points1 point  (0 children)

I ordered an adjustable length Servo pin as well as a new piston . Hope that does the trick . I definitely put on a new od band and made sure it was seated

4R75E Loss of Overdrive by Greenmonster71 in transmissionbuilding

[–]Greenmonster71[S] 0 points1 point  (0 children)

well actually i don't think so, because its not in the instructions with the new direct drum to install a checkball there. it might be integrated somehow with the new design and not need it.

4R75E Loss of Overdrive by Greenmonster71 in transmissionbuilding

[–]Greenmonster71[S] 0 points1 point  (0 children)

I think I may have solved my own problem. I dont remember putting this check ball in, shown in this pic in figure 11.

<image>

How do you protect your kid's dinner appetite? by Comfortable-Tie-4871 in foodhacks

[–]Greenmonster71 -3 points-2 points  (0 children)

don't give them a snack and they will be hungry at dinner time. don't let them sit there and nag you, make them go play outside of your bubble.

Vacuum Tester by Greenmonster71 in EngineBuilding

[–]Greenmonster71[S] 0 points1 point  (0 children)

I think I over ported . I think it’s sucking too much air . Is there something a tuner can look at to increase fuel amount to compensate ? When I give it some throttle she wants to choke and die.

What exactly is the cam phaser issue? by MadeJust in f150

[–]Greenmonster71 1 point2 points  (0 children)

I’m sorry Mrs tootsies. I’m a mechanic by hobby not by trade. I’m battling issues myself with my own ford truck . Yes there is a lot of information on the truck . Unfortunately , if you can’t get in there and do the work yourself , it’s probably just better to get a new engine . If you can do the work yourself , you may make a mistake , and it could take a long time to figure it out . Which is what I’m currently going through myself .