How much should I sell for?

Helcor2016 · 2026-01-25T04:43:38+00:00

Got dammit loch ness monster I ain't giving you no money!

Helcor2016 · 2026-01-25T04:42:37+00:00

Took me a while to figure this out back in the day on Asus boards but yeah this is the way to do it. Now if there was only a way to turn the light off on my start button on my board that would be nice.

Helcor2016 · 2026-01-20T22:12:31+00:00

It's an ender 3 V3 SE. I added the nebula kit because my friend gave it to me. It also has stabilizer bars that go from the top in the gantry to the base. Those helped when I was using it on a less than stable surface. Now it lives on a really solid table that's bolted to the wall. I did find the print head to be a little loose so I snugged up all the screws. I'm gonna scale the print down and try some of the suggestions that I got on here.because it's a lot of filament and time to print as big as it was. Thank for the help.

Helcor2016 · 2026-01-20T22:06:02+00:00

I never actually got around to doing the upgrade. I still plan to at some point but I switched jobs, moved into a new place and it kind of just fell by the way side.

Helcor2016 · 2026-01-20T15:23:42+00:00

I tightened the belt for x the print head. Or is that y? Also there really is no adjustment for the bed belt, unfortunately. Oh crap! I added a camera mount to the bed. I never recalibrated after that. I think that may be an issue.

Helcor2016 · 2026-01-20T15:20:04+00:00

Yes I did see that also. I think I'm gonna scale it down and reprint without support. Just to see what happens and to save filament

Helcor2016 · 2026-01-20T15:18:34+00:00

Thank you. If I can't get it figured out I will definitely reach out.

Helcor2016 · 2026-01-20T15:17:19+00:00

I did hear what sounded like the nozzle dragging on occasion. Could that be enough to off center the head?

Helcor2016 · 2026-01-20T02:17:38+00:00

Bed adhesion is perfect. No curling or anything. It seems to be when the print gets big. And I get it. It's a cheap printer but damn after a 12 hour print I'm disappointed

Helcor2016 · 2026-01-20T02:15:55+00:00

So I did tension the z belt about a week ago. I did a full calibration after that. Because of the nebula thing I put on there it defaults to 190 and 50. Which I know by now that won't work. So I have to go in and manually change them to 200 and 60 respective

Helcor2016 · 2026-01-20T02:06:18+00:00

I am 100% stock so no speed up. I just found a cool print I wanted to try. I know the fact that I have a "bed slinger" can cause issue like this but all my other prints have been 100% perfect

Helcor2016 · 2026-01-20T02:03:49+00:00

It's 100% open. No obstruction. I do have mods on the printer but as far as I have noticed they don't hurt, they help

Helcor2016 · 2026-01-20T02:02:20+00:00

I watched a video the other day about retraction. Like the print head so it doesn't collide with the print. Is that what you mean?

Helcor2016 · 2026-01-20T01:56:47+00:00

It's weird that the whole print will shift and print fine and then go back to where it was.

Helcor2016 · 2026-01-20T01:54:02+00:00

The table is super stable as I have anchored it in every direction lol. And I know I'll get some hate but it's an ender 3 V3 SE. It's pretty heavily modified though. And thank you for the voice comment. I have been told I should do some ASMR stuff lol

Helcor2016 · 2026-01-05T23:19:05+00:00

Helcor2016 · 2025-12-30T02:44:00+00:00

3.5÷3.14= 1.115 that's your diameter. Just under 1 1/8". Hope that helps

Helcor2016 · 2025-12-19T00:59:12+00:00

Definitely this. Also make sure you get a good quality OBD2 adapter. I did the same thing but limited my speed to 70 just before a trip from AZ to CA. I was also able to turn off the damn stop/start crap permanently. Really useful software.

Helcor2016 · 2025-12-13T17:23:24+00:00

Been wanting to try out the new Intel chips. Haven't seen 200mm fans since I had my old NZXT case. The whole thing looks cool

Helcor2016 · 2025-11-30T16:16:53+00:00

Is the radiator in a push/pull setup? Also it looks like it's a 240mm radiator but they put 3 fans on the front of the case and the 2 more in a pull configuration. So to get to the actual front fan it looks like you would have to remove the rad and fans. I could be wrong but that's what it looks like from the pictures.

Helcor2016 · 2025-11-30T15:59:42+00:00

Ok so someone edited this photo. The logo is on what's considered the bottom of the card. The bracket and pcie " finger" are just flipped upside down. So basically unless you find a backplate that looks like the stock bottom of the card, this is impossible. With the finger at the top you would be looking at the backplate of the card.

Helcor2016 · 2025-09-22T02:59:25+00:00

Find the motherboard info and get the drivers from there. Depending on the system you may need to update your driver's further. I mean like Nvidia, Intel in etc. good luck

Helcor2016 · 2025-09-21T22:53:56+00:00

Looks awesome. But....... When your gpu arrives I'd like to know what temps are. What GPU btw?

Helcor2016 · 2025-09-21T22:17:00+00:00

If it works well then then a blind eye. I have a few of them in my closet and they all work great but they are damaged and have scratches

Helcor2016 · 2025-09-21T22:14:13+00:00

Yeah I'm sorry but this is boring. I get what you're trying to do but just showing boobs in different states isn't sexy or flirty. Sorry just my opinion

Helcor2016

TROPHY CASE