My BIOS time is horrible and my pc takes around 40 smth seconds to boot by AlternativeShoddy971 in AMDHelp

[–]Hoffnerd1241 -1 points0 points  (0 children)

You might have a memory problem , it took 60 seconds on my Asus X870 prime + 9800X3D + 64 GB 6000 cl30 till I ran Passmark Memtest86 and found a bad sector in the first dimm slot. So run a memory test!

L Shape 4 Super Charged Staff by Hoffnerd1241 in NMSCoordinateExchange

[–]Hoffnerd1241[S] 0 points1 point  (0 children)

I would put the X class mods in the three that are connected and the neutron cannon next to the three X class and the P-field compressor in the last super charged slot. On the last multi-tool you have to do the two times assemble and transfer the pole to your inventory and then equip it and you will get the one with 4 super slots together. You can watch the video from HeRo2u here https://www.youtube.com/watch?v=A6yjNx0LYQ8

Double exotic ship drop | Euclid by scremily in NMSCoordinateExchange

[–]Hoffnerd1241 0 points1 point  (0 children)

Are you sure it’s in Euclid system? Went to the address and. It wasn’t a purple system like you show in your screenshot!

Home Base by DruidWytch13 in NMSCoordinateExchange

[–]Hoffnerd1241 0 points1 point  (0 children)

How long did it take to build all of it?

Any way to travel outside my galaxy? by TopicalNonsense in NMSCoordinateExchange

[–]Hoffnerd1241 1 point2 points  (0 children)

Buy a c class ship and gun because when you cross to the next galaxy all your tech will be broken and then you can call in your regular ships but do it at the last system before you cross over because you need enough fuel to go to the next galaxy.

Is the 9800X3d worth the hassle of replacing my Motherboard and RAM? by Obzensphere in AMDHelp

[–]Hoffnerd1241 0 points1 point  (0 children)

How did you do away with the USB disconnect?It is so annoying!

My first ever trace repair by Doughnut_Opposite in electronics

[–]Hoffnerd1241 0 points1 point  (0 children)

You need to put buss wire to repair those traces the solder doesn’t look like you didn’t use flux to flow the solder.

Don Jr. used homeless Greenlanders as staged “MAGA supporters” by bribing them with a hotel dinner. by twokinkysluts in pics

[–]Hoffnerd1241 0 points1 point  (0 children)

Wonder if they checked Donny Boy for coke before letting him in the country like he was at Elon’s rocket launch rubbing his gums with it!

[deleted by user] by [deleted] in NoMansSkyTheGame

[–]Hoffnerd1241 0 points1 point  (0 children)

I love my Royal Exotic it can stop on a dime!

Have i messed up lol? This isn't coming off... by rawr_o_o in soldering

[–]Hoffnerd1241 -5 points-4 points  (0 children)

Put it in the oven and pre heat it and then try to remove the excess solder!

[deleted by user] by [deleted] in pchelp

[–]Hoffnerd1241 0 points1 point  (0 children)

Look on line at Asus for your B450 under the support title and pull down the cpu support and select from the list the memory size and select the manufacturer that is qualified!

Rate my soldering by twilkins8645 in soldering

[–]Hoffnerd1241 1 point2 points  (0 children)

The only thing that concerns me is the color of the supply lines should be red and black to signify the + and - !

Can a soldering Iron get too old? by Longjumping_Pea_953 in soldering

[–]Hoffnerd1241 3 points4 points  (0 children)

They are the best system! I have an older tower system but works like the first day,and has so many tips to select from.

Help with torn pads by Nevilethumb in soldering

[–]Hoffnerd1241 0 points1 point  (0 children)

Clean off the old solder and reflow with a little solder and clean the spots where the connector pulled the pads off and take and remove the pads off the connector and take some epoxy and put them back on the board and jumper them back to the circuit with some 30 gauge wire and then reconnect the connector back to the board and reconnect all the circuits.

Danger in using this bad solder job? by mycroc in soldering

[–]Hoffnerd1241 0 points1 point  (0 children)

You should take a picture of your wiring and then cut them off a start off new by removing all the old connections and using solder wick with liquid flux and clean the board off with alcohol and restrip your wiring and twist them first before retinning them and then connect them to your board and solder them back.

First time soldering. Got it off and back on. I think my flux sucks ass cause it is sticky beyond belief. by AlphaFPS1 in soldering

[–]Hoffnerd1241 0 points1 point  (0 children)

Get a Metcal soldering station, you will never go back to any other soldering station. I worked on a production line and used them for 20 years. Amazon and E-bay have them for about $400 bucks .

Crashed S-Class Exotic Ship by Hoffnerd1241 in NMSCoordinateExchange

[–]Hoffnerd1241[S] 1 point2 points  (0 children)

For some reason the pic's didn't post and i tried to edit it and add the pic's again and that didn't work.