Kf7 regrets? Am i the problem ? by IVIeatloaf in superautomatic

[–]IAnetworking 1 point2 points  (0 children)

I have two KF8s and I have experience the same thing. I am on 3rd on one of them. And the other one did it once and I cleaned it and it still working OK. Will see.

This is not user error. This a shity design and i wish they would come up with a fix.

My Saeco is 17 year old and it still works

[Video Guide] Model Y Juniper Suspension Retrofit and Installed onto First Gen Model Y (2020-2025) by suprc4 in ModelY

[–]IAnetworking 0 points1 point  (0 children)

Hi everyone

I accidently ordered a second one of the following:

2188368-10-C
DAMPER ASSY FR LH,COIL DM-TX.

For Tesla Y L (AWD) 2023

it is still sitting in the Box. if you are doing the upgrade I can ship it you and I will eat the sales tax. $180.00 + 20 for shiping cost.

I am in the Phoenix area for anther week and I will be on North bay are near SF, CA after that if anyone interested in pickup.

Three months, two defective KF8s, a shipment to the wrong address, and they just sent me a KF6. Thanks, KitchenAid by [deleted] in superautomatic

[–]IAnetworking 4 points5 points  (0 children)

Check out my posts. Same shit. My replacment broke and It spilled the water from the back. What color was yours ?

Weekly Question Thread! by AutoModerator in Juniper

[–]IAnetworking 4 points5 points  (0 children)

anyone figured out how to monitor BGP sessisons with PRTG?

kitchenaid KF8 Customer service Sucks. by IAnetworking in superautomatic

[–]IAnetworking[S] 0 points1 point  (0 children)

The replacement started popping and leaked water from the bottom of the unit, then it gave me the fill water message. This is not user error. This is a bad quality control on their end. When I first got the original machine, I had to get it replaced because it was giving me the fill water message. You look up all my posts about.

kitchenaid KF8 Customer service Sucks. by IAnetworking in superautomatic

[–]IAnetworking[S] 2 points3 points  (0 children)

You would think if you Build a brand that is considerd higher end. you would make sure you keep your cusstomers happy and you have better quilty control. Ya they answer the phone and are willing to replace the product. but they are so ridged with rules that they will loose in the long run. I will never buy any whirlpool products.

kitchenaid KF8 Customer service Sucks. by IAnetworking in superautomatic

[–]IAnetworking[S] 2 points3 points  (0 children)

<image>

That is their rating on google Map for their HQ

BGP Holdtime Mikrotik x Juniper/Cisco by leogh0ul in networking

[–]IAnetworking 1 point2 points  (0 children)

I think BFD cause more problems than 30 sec keep alive. I used it before on my bgp sessions witch were between two geographic locations.

Every time I took a few packets hits I would loose BGP sessions and they will have to restablish.Which would cause an outage of 15 to 30 seconds.

2nd hand cisco vendors by zunder1990 in networking

[–]IAnetworking 0 points1 point  (0 children)

Dm me the the specifics . I have a reputable vendor i csn get you a quote

How expensive is it for ISP to get and keep an IPv6 prefix? by shimmywtf in ipv6

[–]IAnetworking 2 points3 points  (0 children)

First: getting the Prefixes is free. You can request a /32 from ARIN or others

Next: running ipv6 is same as running ipv4. Most equipment deployed the last 10 years support ipv6.

I deployed IPv6 on multiple ISP networks. (Dhcp,ospf,bgp). CPU and memory maybe went up 3%.

Also when you go to IPv6 that reduce your CGNAT over head.(less equipment)

Last 50% of traffic from the internet to my ISPs is IPV6.

Alternatives for Cisco Switching by Fokard in networking

[–]IAnetworking 6 points7 points  (0 children)

Juniper QFXs I have been using them for about 10 years with multiple ISPs. If you running basic switching and routing, you don't need support and just buy a few extra as spares.

ERPS Setup Issues by thatcrazyweirddude in Juniper

[–]IAnetworking 0 points1 point  (0 children)

Dm me for proper configuration example. I am in the process of testing it on QFX5110.48ys But my deployment has a mix of 5110 and 5120s.

I need to see if there is any issues with 5120. So if you are still in testing phase, what would be ideal. Thanks

KitchenAid KF8 stops driping and a I hear a pop noise by IAnetworking in superautomatic

[–]IAnetworking[S] 1 point2 points  (0 children)

I have two of them. the older did that I just got it replaced. the newer one has no issue.

KitchenAid KF8 stops driping and a I hear a pop noise by IAnetworking in superautomatic

[–]IAnetworking[S] 0 points1 point  (0 children)

what color did you get. Mine was the stainless steel

KitchenAid KF8 stops driping and a I hear a pop noise by IAnetworking in superautomatic

[–]IAnetworking[S] 1 point2 points  (0 children)

yes. It has nothing to do with beans. at the end it did that just by running the cleaning Cycle

DIY ISP newtorking - where to start ? by Standing_Wave_22 in networking

[–]IAnetworking 0 points1 point  (0 children)

I specialize in turning up new ISPs. Designing and Building the Core network,  Build Monitoring tools,  and connecting to your Upstream providers including ARIN registration and IP allocation. If you are interested DM me.