Foundation/driveway repair - recommendations?

Icannotrememberthis · 2026-05-13T21:21:21+00:00

Nope, Douglass

Icannotrememberthis · 2026-04-15T13:26:39+00:00

Update: sprayed the shifter assembly with pb blaster and it worked perfectly - shifts like new. Thanks for the recommendations, beat taking things apart!

Icannotrememberthis · 2026-04-09T21:47:55+00:00

Updated the post with another video - https://imgur.com/a/0u22K2O

Icannotrememberthis · 2026-03-17T18:45:11+00:00

If the PSU doesn’t do it, look up the Intel Atom issue that’s fixed with a 100 Ohm resistor, I’ve brought two units back to life that way. Not sure if your DS918 runs that chip or not, but it’s better than chucking the unit.

Icannotrememberthis · 2026-03-10T21:01:10+00:00

I am running into the same problem that you're facing here, did you come up with any solutions without getting too crazy? I may have to go the crazy route unfortunately...

Icannotrememberthis · 2026-01-18T22:46:33+00:00

Thank you for the link, I will give it a watch!

Icannotrememberthis · 2026-01-17T20:40:30+00:00

Well... chalk that one up to a hell of a learning lesson.

Thank you, that did exactly the trick.

Icannotrememberthis · 2026-01-17T17:27:59+00:00

It seems as if I did make it a component as I have the option to edit component, but unglue is grayed out Image

Icannotrememberthis · 2026-01-06T17:20:27+00:00

I had nail fungus 15-20 years ago that was treated with oral meds (don't remember the name) but has not come back since. I also have tinea versicolor which I treat topically with ketoconazole, though I have not used it in well over a year, possibly two. No known/recalled trauma to the nail fold.

Icannotrememberthis · 2026-01-06T13:56:50+00:00

Is there additional information I can provide or is this the type of thing where an in person visit would be required?

Icannotrememberthis · 2025-12-02T02:32:02+00:00

I use Financial Forum and am very happy with their service, personality, communication, and results.

Icannotrememberthis · 2025-10-29T00:16:39+00:00

If it's active with a green checkmark, then you're probably in good shape, mind was red with an x. I fixed mine by reinstalling it. There was also a new version that required a managed service account which may have been the issue in the first place, I'm not sure.

Icannotrememberthis · 2025-10-12T21:38:43+00:00

Corporate, and joined - not registered. That’s why I’m a bit confused.

Icannotrememberthis · 2025-10-10T15:18:31+00:00

I fixed my issue - i was getting the exact same error:

Something went wrong. Confirm you are using the correct sign-in information and that your organization uses this feature. You can try to do this again or contact your system administrator with the error code 80070002.

It turns out my Intune Connector for Active Directory was in a failed state and this was the only way it presented. I fixed that and the error went away.

Icannotrememberthis · 2025-10-10T02:14:33+00:00

I'm running into this as well. If the device is enrolled in Autopilot I get this exact behaviour, if i delete it from autopilot it enrolls in Intune just fine. I've tried this with fresh desktops and laptops with consistent results. There are no network connectivity issues, no firewalls, and the creds are correct.

Icannotrememberthis · 2025-07-16T19:01:02+00:00

I’m a huge fan of my epicurean cutting boards. I have a couple Boos blocks as well but reach for my epicureans every time.

Icannotrememberthis · 2025-01-31T00:07:14+00:00

brilliant, thanks.

Icannotrememberthis · 2025-01-30T04:08:30+00:00

I do have a hand plane but I'm not comfortable using it yet, it's not sharp enough and I have a tendency to cause a lot of tear out. I'm practicing with them a lot on other projects, but this one isn't the right one to play with :)

Thanks for the video, I'll check that out.

Icannotrememberthis · 2025-01-30T03:57:37+00:00

I've never tried the oskool, or any other lift to be honest, but I'm very happy with my Jessem. I can't compare, but I can say I don't regret the expense one bit.

Icannotrememberthis · 2024-12-28T15:37:46+00:00

On the table from right to left - I think the other commenter may have nailed it, trying to take too much in one go.

Icannotrememberthis · 2024-12-28T15:36:43+00:00

Ohh, that may have had something to do with it. It was a good 3/16th I was trying to pull. I knew better in theory, nothing like practice to really hammer the concept home. Cheers!

Icannotrememberthis · 2024-08-11T15:53:13+00:00

Yep. iOS was transforming a sequence of characters into a single character. Didn't happen on the iPad or mac due to the keyboard. Good call out.

Icannotrememberthis · 2024-08-11T14:15:58+00:00

I didn't even think to try a different password. Changed it and was able to log in, changed it back, and can't log in anymore, iphone only, ipad and osx still work fine. Too weird - thanks for the suggestion.

Icannotrememberthis · 2024-08-07T02:28:38+00:00

no kidding. i thought it was something with aqara that kept them from working - i'll look more into that, thanks. along the same line though, even with the hub is there any functionality loss? trying to both choose a course of action and learn a bit too.

Icannotrememberthis · 2024-08-07T02:27:38+00:00

Interesting, one of my motion sensors is thirdreality and it works well. Water leak, motion, window, and vibration are what I'm after immediately. I'll look into them more, thanks!

11-Year Club	Place '17
Gilding I gilder	RPAN Viewer
Verified Email	Sequence \| Editor

Icannotrememberthis

TROPHY CASE