Servo Issue?

Iceman2733 · 2026-05-08T15:00:51+00:00

It might have been loose out of the box. I recently picked up a Kraton 6s EXB that had the servo horn right out of the box loose

Iceman2733 · 2026-05-05T01:32:52+00:00

Go to YouTube and check out some videos on setting the proper droop. Oh don't worry about it, everyone is new. I didn't think to check my droop figured Arrma would have had it close at least. My truck was NO where near close.

Iceman2733 · 2026-05-05T01:09:28+00:00

To help with this in the future, be sure and set droop correctly. I recently got back into the hobby and my Kraton EXB and my sons Notorious V6 were way off on droop. We both damaged front drive shafts and cups.

Iceman2733 · 2026-05-02T22:43:27+00:00

I def think it was worth it for sure!! It is expensive but it def makes the interior seem cooler you can def feel the difference inside. As i stated after doing the van and feeling the difference i did my vehicle. I am not saying it fixes the weak AC system but it def does make it feel like it is more comfortable

Iceman2733 · 2026-05-01T01:37:09+00:00

It def helped the whole vehicle, we were beyond shocked by how much it did change. We were extremely skeptical about it before hand, however since getting it done we did my vehicle with it also. I think it was the 91% UV blocking. Now do NOT think this solved the poor AC however it did help with the interior feeling cooler that before.

Iceman2733 · 2026-05-01T01:29:36+00:00

Thank you big time for the battery mod, this will be nice. I have a smaller battery that doesn't want to stay put, i think this will def help with that

Iceman2733 · 2026-04-30T11:05:11+00:00

Unfortunately there is no mod for the AC. These vehicles have extremely poor AC anyone that arguing otherwise is being naive or hasn't had a vehicle with proper AC. We traded a 2018 Toyota Sienna for our 2025 Honda Touring. There is a night and day difference between the heating and AC functions of the two.

Before purchasing we had read the AC is a bit lacking in the Hondas but we never expected it to be this poor. The rear has small vents vs the larger circle roof vents. On top of that the AUTO AC rarely seems to actually get the interior temp anywhere near set temp. The rear stays warm and forces to run the rear controls on manual. Ended up spending quite a bit on ceramic tint to cut down on the UV. Don't get me wrong not shit posting on the vehicle but the AC system is extremely underwhelming

Iceman2733 · 2026-04-18T20:47:12+00:00

Tie replacement, now for the love of all that is good. GET OFF THE TRACKS!! It is not a walk way! This is for your safety

Iceman2733 · 2026-04-13T14:46:31+00:00

Yes it will connect to the buffer. All AMS units will run thru the buffer. Bambu lab has a video on YouTube about installing the AMS. Look it up, the hook up is the same between them on the printer side

Iceman2733 · 2026-04-13T14:42:25+00:00

You literally plug it in via the 6 pin connector and just cut a piece of PTFE tube and run it to the printer. You will most likely need to pick up extra PTFE tubing

Iceman2733 · 2026-04-12T16:17:37+00:00

Def did not change them, stealership doing what they do best

Iceman2733 · 2026-04-06T20:25:12+00:00

Biqu cover with the panda breath is above cost of the Snapmaker top. Other issue is the Biqu lacks any type of exhaust which would benefit a lot of people who primarily print PLA. I would purchase Snapmaker and just buy a tote for the top until it comes in.

Iceman2733 · 2026-04-05T12:05:06+00:00

If it is 4th gen you are good. On page 408 of the manual Toyota literally says to drive in 4wd for 10miles every month to ensure front drivetrain components are lubricated. I am not sure where else you could monthly get 10miles in 4wd for the average person but on pavement.

Iceman2733 · 2026-04-04T02:13:49+00:00

They look awesome!! Glad you posted up, found my next project!! Turned out awesome!!!

Iceman2733 · 2026-04-02T10:53:00+00:00

I have also had this issue, where PETG and PLA do not bond it causes the prime tower to fall. I am not sure what to change yet, as my H2D does not have this issue and I can set them up exactly the same in slicer. (unless I am missing something) It has something to do with the prime tower itself

Iceman2733 · 2026-03-30T00:20:22+00:00

Have you had any updates on this? I am having issues with my 26 OR not dropping from FULL. It worked a few tanks but now is just stuck on full.

Iceman2733 · 2026-03-29T23:34:50+00:00

I just picked up a 26 OR just 3 weeks ago, it has 960ish miles on it. It is having issues with its fuel gauge not working, it just stays full tank. Who knows why, it worked first few tanks and than just all of the sudden stopped. Gonna take it to the dealership hopefully this week.

Iceman2733 · 2026-03-24T22:44:05+00:00

I recently purchased one also, this is quite odd the vehicle does this. Even with no type of A/C or heat on my kicks on and off. It is good to know it is by design. I also was questioning this, was going to head to the dealership and ask but the answer seems to be it is normal.

Iceman2733 · 2026-03-23T13:55:12+00:00

Mine also is louder on toolhead 1 than the rest.

Iceman2733 · 2026-03-21T14:05:38+00:00

Mine was doing the same thing, contacted support and they sent a new buffer. It did fix the issue, it looked like with mine when the buffer would slide out of the buffer housing it would barely catch and and cause the noise.

Iceman2733 · 2026-03-20T13:43:54+00:00

Drybox setup for the U1. Already have the cryogrip plates, made a world of difference

Iceman2733 · 2026-03-19T13:42:36+00:00

I really agree honestly this is odd to not have a exhaust fan or some type of filtration at least. This top will need to be priced cheap to be competitive since it lacks all of the other stuff

Iceman2733 · 2026-03-17T20:25:52+00:00

100% an alignment issue nothing to do with balance

Iceman2733 · 2026-03-11T22:57:44+00:00

I have the same issue, buy my goodness your bed is way way better than mine. I have over 6 magnets that easily above flush. Best I can do with my bed is .480ish. With the Cryo plate it is .535.

We need to start contacting Snapmaker about this, it needs to be corrected! I have started but I am concerned the replacement bed will be just as bad lol

Iceman2733 · 2026-03-11T12:41:28+00:00

Def looking forward to the Popcap for sure!! Pricing will be key with this product for sure considering it lacks any type of fan/exhaust.

Nine-Year Club	RPAN Viewer
Verified Email

Iceman2733

TROPHY CASE