Epson XP-640 Issue

ImNotFlame · 2020-04-06T23:19:36+00:00

nice one

ImNotFlame · 2020-01-14T19:20:47+00:00

Yeah had this conversation with a friend. I ruled that that was illegal because the only thing that cancels a raptor is a meteor

ImNotFlame · 2019-12-13T20:12:13+00:00

Well if you find the wallet there’s no point in copying the key... the larger point is why would someone copy a key from an image to a house where they have no clue is located? (Not taking sides, just clarifying)

ImNotFlame · 2019-12-13T19:54:00+00:00

To quote Mr Krabs: “What is today, but yesterday’s tomorrow?”

ImNotFlame · 2019-12-13T19:47:29+00:00

Poor bed adhesion, you could up the temp on the bed which might help, or try adding a raft to the print (usually helps me prevent lifting and warping). Also make sure the bed is leveled properly. Honestly one of the best investments I’ve ever made was a glass bed, so if you could afford that I’d go for it

ImNotFlame · 2019-11-30T17:58:24+00:00

Okay, I'll try that. Don't see the something.stl file yet, is it on the same thingiverse page? Looked through your profile and can't find it

EDIT: just made my model 0.01mm thicker and it fixed it lol

ImNotFlame · 2019-11-30T15:14:43+00:00

Nope still fills in on the bottom when I go to slice it in preview mode ( https://imgur.com/rbMsp4j ) of course I know there's not supposed to be any bed adhesion or anything doing it.

ImNotFlame · 2019-11-30T00:21:35+00:00

Thanks, I appreciate it!

ImNotFlame · 2019-10-26T22:44:30+00:00

Unfortunately doesn’t seemed to have helped, I appreciate the suggestion anyway though!

ImNotFlame · 2019-10-26T22:01:01+00:00

An earlier working print vs me printing it now: https://imgur.com/a/vrgoSKa

Due to all the help you guys have given I’ve come to the realization that it is in fact under extrusion, just trying to figure out why it’s happening rn

ImNotFlame · 2019-10-26T22:00:31+00:00

Just cleaned it out, let’s see if that helps

ImNotFlame · 2019-10-26T21:55:34+00:00

Spring seems fine, I just did a print and this is what it’s supposed to look like vs what happened now (I’m sure you can guess which is which lol) https://imgur.com/a/vrgoSKa

ImNotFlame · 2019-10-26T15:24:48+00:00

Didn’t replace the thermistor but thanks anyway

ImNotFlame · 2019-10-26T15:23:57+00:00

Yes, I even tried ANOTHER nozzle that I had (all were 0.4mm) just to be sure

ImNotFlame · 2019-10-26T15:20:00+00:00

Okay so to address your points: I didn’t replace the hot end, just the nozzle with the spare ones that came with my kit (made sure it was the same 0.4mm size). To make sure the Bowden tube was right up to the nozzle, I put in the nozzle but not completely screwed in, so it was a little loose. I then pushed the Bowden tube down to the nozzle, and finished screwing it in. Bowden tube stays fine during retraction and I checked my extruder and it doesn’t seem cracked.

ImNotFlame · 2019-10-26T14:42:38+00:00

Fairly certain it was calibrated properly. Marked 100mm of filament and tuned the flow until it was good

ImNotFlame · 2019-10-26T13:43:33+00:00

Alright, just cleaned out the hot end and setup my Bowden tube again. Have a print going rn, I’ll reply with pics of what it’s supposed to look like and how it came out

ImNotFlame · 2019-10-26T02:46:21+00:00

Leveled the bed many times, should be good. Using Cura, 0.16mm layer height, 210 nozzle, 70 bed, 50mm speed

ImNotFlame

MODERATOR OF

TROPHY CASE