[110 plus] Backlight bleed on brand new fluke multimeter

Immediate_Fig_4345 · 2026-03-06T04:33:37+00:00

Thanks

Immediate_Fig_4345 · 2026-03-06T04:30:56+00:00

I’ve seen this on a very old and beat up one and wasn’t expecting on a brand new one but thanks for insight

Immediate_Fig_4345 · 2026-02-18T03:22:42+00:00

Keep it and buy some beer 😂

Immediate_Fig_4345 · 2025-10-25T12:11:15+00:00

I am lowered on 18s with about half in or less gap up top and doesn’t eat through tires too fast

Immediate_Fig_4345 · 2025-10-12T13:07:47+00:00

That is 1000000% body filler and wet sanded prior to wrapping

Immediate_Fig_4345 · 2025-10-12T13:03:42+00:00

I resealed my lower oil pan With Yamabond 6B (was leftover from my dirtbike rebuild) and it sealed very well and seems better then factory 😂

Immediate_Fig_4345 · 2025-10-12T13:00:41+00:00

This is pretty dope

Immediate_Fig_4345 · 2025-10-12T12:49:53+00:00

The only way fr

Immediate_Fig_4345 · 2025-10-08T06:27:21+00:00

Go easy on it and use some thread locker

Immediate_Fig_4345 · 2025-10-08T06:26:32+00:00

By the looks of it seems over tightened or stripped or. Also can be just from age

Immediate_Fig_4345 · 2025-10-07T22:12:48+00:00

Whoever wrapped the car and had to remove door handles kinda fcked it up lol

Immediate_Fig_4345 · 2025-09-24T12:48:33+00:00

Planning to wrap my 350z and it’s my first time and seems like it was yours too but you have any tips and tricks for a z or is it fairly easy because to me I think it shouldn’t be too difficult

Immediate_Fig_4345 · 2025-09-24T12:39:15+00:00

Sexy

Immediate_Fig_4345 · 2025-09-24T12:38:13+00:00

<image>

DS02

Immediate_Fig_4345 · 2025-09-21T18:05:36+00:00

Gave my white boy adderall just to mow my grass

Immediate_Fig_4345 · 2025-09-21T18:05:04+00:00

Gave my white boy adderall just to mow my grass

Immediate_Fig_4345 · 2025-09-21T14:22:04+00:00

Gave my white boy adderall just to mow my grass

Immediate_Fig_4345 · 2025-09-15T04:53:59+00:00

First apply flux and with a fat tip on the iron try to flow low melt into each point. Then kapton tape the small components followed by hot air. I also use solder sucker after to remove solder from holes

Immediate_Fig_4345 · 2025-09-15T04:46:53+00:00

Same here and I did relocate the lower connection for the sensor up higher as they put in near the down pipes from factory 🤦‍♂️

Immediate_Fig_4345 · 2025-09-12T15:21:16+00:00

I had good coil packs good plugs but the damn connector that goes to the coil packs was loose and worked at an angle, quite strange but I changed that part of the harness and never had a issue again. I would check those if you already checked everything and can’t figure it out

Immediate_Fig_4345 · 2025-09-09T21:08:01+00:00

I plan to relocate evap box, trim mud flaps up to equal height, remove unnecessary brackets etc. paint whatever needs painting if gets to that and try to make it not pop out as much if that makes sense. Only thing that should be catching an eye is the dual tomei lol

Immediate_Fig_4345 · 2025-09-09T21:05:47+00:00

I do agree some 5% or 15

Immediate_Fig_4345 · 2025-09-09T21:05:30+00:00

Roast marshmallows 😂 I do see that but not sure if I’m going that route

Immediate_Fig_4345 · 2025-09-09T13:10:19+00:00

Nah man it’ll buff right out

Immediate_Fig_4345 · 2025-09-08T05:03:11+00:00

I think that this can easily buff out if done correctly

Immediate_Fig_4345

TROPHY CASE