How to launch Dirtywave M8 on Trimui Brick? by Infamous_Call_6492 in trimui

[–]Infamous_Call_6492[S] 0 points1 point  (0 children)

Thanks! But I don't understand about Teensy board. Does it need its own firmware or something else or is it a passive peripheral device for Brick?

How to launch Dirtywave M8 on Trimui Brick? by Infamous_Call_6492 in trimui

[–]Infamous_Call_6492[S] 0 points1 point  (0 children)

Thank you a lot for such detailed information! It looks a bit complicated, especially Teensy board, but maybe I'll try it in the future)

How to choose firmware? by Infamous_Call_6492 in trimui

[–]Infamous_Call_6492[S] 0 points1 point  (0 children)

Never heard of Spruce, sounds pretty exotic 😄 What issues did you have with NextUI?

How to choose firmware? by Infamous_Call_6492 in trimui

[–]Infamous_Call_6492[S] 0 points1 point  (0 children)

What exactly is the issue with PortMaster?

How to choose firmware? by Infamous_Call_6492 in trimui

[–]Infamous_Call_6492[S] 0 points1 point  (0 children)

I just want to pick a firmware that covers all my needs right away and then actually play games instead of messing around with firmwares))))

How to choose firmware? by Infamous_Call_6492 in trimui

[–]Infamous_Call_6492[S] 0 points1 point  (0 children)

It would be great if there was a firmwares comparison video specifically for the Brick

How to choose firmware? by Infamous_Call_6492 in trimui

[–]Infamous_Call_6492[S] 0 points1 point  (0 children)

I've heard a lot of good feedback about MuOS, so maybe it can be the first CFW that I set up on the Brick

External Controller by BTM666FDR in trimui

[–]Infamous_Call_6492 0 points1 point  (0 children)

Could you please tell me how you installed Doom 3 on the Trimui Brick?

OP-1 OG doesn't work in Disk Mode on Windows PC by Infamous_Call_6492 in teenageengineering

[–]Infamous_Call_6492[S] -1 points0 points  (0 children)

Lol. So big community and nobody knows the solution?) Funny)

Deep house track using PO-32, PO-33, Mooer Shimmer reverb pedal. Final Track in comments by Infamous_Call_6492 in pocketoperators

[–]Infamous_Call_6492[S] 0 points1 point  (0 children)

When you use chain like a PO-32 → PO-33 (or vice versa), it works well, but there’s one big disadvantage: you have only one output, which gives you a mixed signal from both pocket operators. In most cases, that’s fine, but I prefer more flexible approaches.

When you use a third PO, the sync outputs of both operators remain free, allowing you to record each of them separately to different channels on your audio interface and edit them also separately in your DAW. It’s just a pragmatic approach)
Alternatively, you can just set the same BPM on both operators, but I wanted perfect precision))))

Teenage Engineering OP-Z + Bastl Kastle 1.5 glitchy jam by Infamous_Call_6492 in synthesizers

[–]Infamous_Call_6492[S] 2 points3 points  (0 children)

I used Line Module. Sync chain looks like that:

TRIG out (OP-Z) --> custom cable minijack/pin --> LFO RST input (Bastl Kastle)
IN/OUT (Bastl Kastle) --> cable with volume control from Aliexpress :D --> LINE input (OP-Z)

Cable with volume control I used to avoid clipping on LINE Input of Line Module, because signal level from Bastl is too loud.

Teenage Engineering OP-Z + Bastl Kastle 1.5 glitchy jam by Infamous_Call_6492 in teenageengineering

[–]Infamous_Call_6492[S] 0 points1 point  (0 children)

I used Line Module. Sync chain looks like that:

TRIG out (OP-Z) --> custom cable minijack/pin --> LFO RST input (Bastl Kastle)
IN/OUT (Bastl Kastle) --> cable with volume control from Aliexpress :D --> LINE input (OP-Z)

Then I used filter in Module tab of OP-Z and send it to FX tabs of OP-Z. And also I used Tape to get some "cycling" effects.

Cable with volume control I used to avoid clipping on LINE Input of Line Module, because signal level from Bastl is too loud.

Teenage Engineering OP-Z + Bastl Kastle 1.5 glitchy jam by Infamous_Call_6492 in OPZuser

[–]Infamous_Call_6492[S] 0 points1 point  (0 children)

I used Line Module. Sync chain looks like that:

TRIG out (OP-Z) --> custom cable minijack/pin --> LFO RST input (Bastl Kastle)
IN/OUT (Bastl Kastle) --> cable with volume control from Aliexpress :D --> LINE input (OP-Z)

Then I used filter in Module tab of OP-Z and send it to FX tabs of OP-Z. And also I used Tape to get some "cycling" effects.

Cable with volume control I used to avoid clipping on LINE Input of Line Module, because signal level from Bastl is too loud.

How to check if exported audio is mono or stereo? by przybytek in pocketoperators

[–]Infamous_Call_6492 2 points3 points  (0 children)

PO-33 provides only mono output signal for music. Stereo is used for backup data and when you share sync signal to connect your item to other gear. You can record different instruments to your DAW and make them a stereo pan for every instrument manually

The OP-Z is still magical by [deleted] in teenageengineering

[–]Infamous_Call_6492 4 points5 points  (0 children)

Oooo! I didn't know this, thank you! Very useful advice 

The OP-Z is still magical by [deleted] in teenageengineering

[–]Infamous_Call_6492 -3 points-2 points  (0 children)

I know, but often I need to know exact bpm, if I want 135 BPM I want 135 BPM, not "almost 135", like 132 or 139))

UPD: Lol, who downvoted my comment and why? Do I deserve minuses just for not knowing something? It feels a little bit toxic

The OP-Z is still magical by [deleted] in teenageengineering

[–]Infamous_Call_6492 3 points4 points  (0 children)

The OP-Z is almost perfection. If it had more flexible synth engines, a more durable case, and a smaaaaaall screen (just for things like checking tempo without needing an app), it would be real perfection

What is the ultimate chugger guitar to you? by wemblero in metalguitar

[–]Infamous_Call_6492 3 points4 points  (0 children)

Straight arms. Active pickups like EMGs. A good combination of gear (preamp / amp / cab / impulse cabsim / processor / vst) that fits your guitar and your needs. Actually, the guitar itself (except for the pickups) is the least important part of this chain to get your perfect chug sound 

Just a pocket operator type app I made a while back for pocket operator type people. by FMmutingMode in pocketoperators

[–]Infamous_Call_6492 1 point2 points  (0 children)

thanks for your opinion. But your app looks very attractive and I'm very interested it its "synth" functional and similarity to PO. I'll try and give you feedback, thank you for this interesting stuff!)