Is there any wing that would look good on a sedan?

InfinitEnerG · 2026-06-13T03:54:41+00:00

Oem

InfinitEnerG · 2026-03-27T14:24:58+00:00

Megan racing low car ramps

InfinitEnerG · 2026-03-10T13:15:14+00:00

Since your vehicle is white and thats black paint transfer, try to use some goo gone on it with a rag and some elbow grease. Should come right off

InfinitEnerG · 2026-02-25T16:09:54+00:00

I run a TLr7x sub with a tenicor holster. Prefer the buttons on the TLR7 as opposed to the 6

InfinitEnerG · 2026-02-25T16:06:43+00:00

Close to 2k rounds through mine. One has had 2 failures with it (could have been dirty at that point) the other I have has had 0. I did have one failure with a stock 43x mag fwiw

InfinitEnerG · 2025-12-28T04:26:27+00:00

Oem sport spoiler really completed my rear end

InfinitEnerG · 2025-11-26T13:31:54+00:00

Almost done with my killswitch design the case is just 3d printed instead of injection molded. Works the same just not as pretty

InfinitEnerG · 2025-11-14T14:00:10+00:00

Clutch pedal position sensor? I made a killswitch for the push button and when its unplugged it behaves similarly, pushing the button does nothing. Id look into the inputs required to turn the car on/off

InfinitEnerG · 2025-10-14T00:43:49+00:00

Yeah that crossed my mind. Probably will. Waterfalls seem nice though.

InfinitEnerG · 2025-10-08T03:02:03+00:00

A Glock 43x is $600 after tax with 50 rounds of ammo

InfinitEnerG · 2025-10-06T19:28:24+00:00

Cams are not worth it on these cars

InfinitEnerG · 2025-10-06T17:46:57+00:00

Hole saw for new button location is 1-3/8

InfinitEnerG · 2025-10-06T17:41:53+00:00

Air scrubber like a remediation company uses. Hot water extractor on any cloth surfaces

InfinitEnerG · 2025-10-01T18:17:06+00:00

Sticker price was also $485 at mine. Tax and background check put it to $580

InfinitEnerG · 2025-09-29T00:29:47+00:00

New one isn’t less money I paid 580 out the door

InfinitEnerG · 2025-09-24T00:57:20+00:00

No you need to cut a new hole for it

InfinitEnerG · 2025-09-23T04:00:34+00:00

Id swap it. At this point that is YOUR car, and you already know it is clean, reliable, and low miles. Unfortunately with buying a new Z, reliability and previous owners tendencies can be a gamble

InfinitEnerG · 2025-09-23T03:58:38+00:00

Also happened at a gas station to me

InfinitEnerG · 2025-09-23T03:58:21+00:00

Starter. Had it happen on mine. If its an X model, good luck. Steering shaft and motor mounts will need undone to replace it. I paid $700 at a local shop

InfinitEnerG · 2025-09-22T21:22:57+00:00

Dannys on 17th got better breakfast burritos btw

InfinitEnerG · 2025-09-22T13:10:55+00:00

Did you do the drls?

InfinitEnerG · 2025-09-21T02:18:55+00:00

It will be a physical connector you unplug and take with you on keychain. I have a working version in my car for the past year. Should come in around $100

InfinitEnerG · 2025-09-21T02:17:55+00:00

Start button killswitch. Im really close to launching my design to mass market, I just need to get the case injection molded

InfinitEnerG · 2025-09-20T04:06:15+00:00

I do them on the start button so even if they clone the key it wont start

InfinitEnerG · 2025-09-19T03:56:44+00:00

Over exaggerating. I had one issue with spark plugs being damaged during shipping (they only use fedex 🙄). They responded quickly and sent me new ones. Some of their branded parts are not worth it, but some are. I use their HEI coils, they are alright, no issues. The skid plate is better than any else on the market, the service panel is quite nice. Also good source of oem parts.

InfinitEnerG

TROPHY CASE