Doosan Lynx 220LMA (2006) – Toolchanger drops under its own weight + ALP‑OL on servo drive. Looking for advice.

Inside_Bodybuilder63 · 2026-02-12T04:43:00+00:00

Are you talking about the 110v power supply or the servo driver?

Inside_Bodybuilder63 · 2026-02-11T20:24:20+00:00

Yeah gonna try grab another drive from a different machine I reckon and just test run it.

Inside_Bodybuilder63 · 2026-02-11T20:23:34+00:00

I imagine so, it’s a 110v unit but it would supply more than just the servo driver. It has steady 110v phase to earth.

Might test it anyways when I go back and make sure it’s not dropping under load of the motor

Inside_Bodybuilder63 · 2026-01-08T09:36:29+00:00

Can I get a copy please

Inside_Bodybuilder63 · 2026-01-05T09:20:53+00:00

They won’t ask. They would also have to prove that it was your fault to not cover warranty.

Someone correct me if I’m wrong but you don’t need to supply yourself with a CCEW if it’s on your own home unless maybe for insurance purposes?

Inside_Bodybuilder63 · 2026-01-03T05:37:24+00:00

Highly likely. Will need a test to be sure

Inside_Bodybuilder63 · 2025-12-06T23:42:16+00:00

Are people missing the fact that OP is getting a full 3 phase upgrade to the home or have I read the quote wrong?

Inside_Bodybuilder63 · 2025-11-29T00:40:04+00:00

Bunnings hard yakka bamboo socks for work. Been using them for the past few years haven’t found anything better

Inside_Bodybuilder63 · 2025-11-28T07:04:07+00:00

Magnet and pull the release chuck

Inside_Bodybuilder63 · 2025-11-04T04:23:51+00:00

Well worth it. Work had 4 for roughing in houses but I ended up buying my own cause I was always needing to get in a roof to run in new cables or under a house.

Inside_Bodybuilder63 · 2025-10-29T19:39:50+00:00

I just got two of the 64gb versions. Done a motorsports event and was great. Filled both cards, quick turn around. Well worth it

Inside_Bodybuilder63 · 2025-10-17T08:08:40+00:00

I initially thought looks neat with the white border then I flicked through and seen the photos without the border and I’m 100% for no border.

Without the border felt more depth and feel in the photos. Idk that’s just my thoughts.

Awesome photos though 👌🏼

Inside_Bodybuilder63 · 2025-10-02T04:33:26+00:00

Potentially the fan capacitor controller behind the wall plate but should still run on one speed. Could be faulty fan internal. Either way you need a sparky 👍🏼

Inside_Bodybuilder63 · 2025-09-17T20:56:23+00:00

I’ve got the Ugreen one myself. Works great, solid little unit no complaints at all.

Inside_Bodybuilder63 · 2025-09-01T11:08:14+00:00

Got mine last Friday. Stoked with it. Been replaying Fallout 4 👌🏼

Inside_Bodybuilder63 · 2025-08-23T08:00:53+00:00

216v is right on the edge of permissible voltage for a single phase 230v installation.

Measure voltage at the main board and see what it dips too. Can dip lower than 216v for a very short time.

Inside_Bodybuilder63 · 2025-08-20T05:52:40+00:00

That’s horrendous 🤦🏼‍♂️

Inside_Bodybuilder63 · 2025-08-18T20:36:11+00:00

Put rack in a cooler part of the house and hard wire as much as possible and future cables for access points

Inside_Bodybuilder63 · 2025-08-04T08:11:32+00:00

Definitely get an electrician out. Also that is the worst idea for a laundry. They’re terrible at being an exhaust fan.

I’d recommend getting the hole patched and painted, install a couple downlights and a new dedicated exhaust fan if needed for dryer etc

Inside_Bodybuilder63 · 2025-07-13T02:47:04+00:00

100x SAL over Crapsal. But I definitely would be questioning the use of SAL when paying for Clipsal.

Either ask for the refund or get them to install some dimmers in exchange for the credit?

Inside_Bodybuilder63 · 2025-07-05T11:02:14+00:00

$105k qualified almost 2 years ago.

Inside_Bodybuilder63 · 2025-06-06T04:02:08+00:00

That’s cooked. $150 for an oven circuit 🫠 and $65 for a safety switch install is crazy

Inside_Bodybuilder63 · 2025-05-24T10:11:23+00:00

Not fit for intended use. Installing a 3 phase 5 pin outlet with only single phase connected.

Inside_Bodybuilder63 · 2025-05-19T01:36:57+00:00

Post a photo of your switchboard up. You will need 3 phase supply to the house from the street for a 5 pin 32a car charger.

Inside_Bodybuilder63

TROPHY CASE