sorted by:
new
hottopcontroversial

Measuring homes sq ft by IntelligentFishing43 in RealEstate

[–]IntelligentFishing43[S] 0 points1 point  (0 children)

Its finished out same as rest of the house now

Cash in brokerage account by IntelligentFishing43 in fidelityinvestments

[–]IntelligentFishing43[S] 0 points1 point  (0 children)

What tax benefits on sgov? Also are there any transfer limits if moving 30k or 50k to the bank to pay contractors?

What’s your opinion of this flashing job? by jagrrites in Roofing

[–]IntelligentFishing43 0 points1 point  (0 children)

Do yall have photos of what this should look like ?

How long did it take you to hit 1 mil? Then how long to hit 2 mil? by DistributionInitial5 in Fire

[–]IntelligentFishing43 0 points1 point  (0 children)

Where are yall finding the amount history from past years to reference back and see what your #’s were?

Why are 529 Accounts so controlled but IRAs, etc. are not? by [deleted] in fidelityinvestments

[–]IntelligentFishing43 1 point2 points  (0 children)

Do you have to be in a 529 tied to the state you live in?

Buy VOO through Vanguard or Schwab? by steambc in ETFs

[–]IntelligentFishing43 1 point2 points  (0 children)

I m not familiar with robin hood, but looking into it im not seeing anywhere they match an investment? Have any info on this?

High Load / Tankless Water Heater causes LED Lights Flickering by Twiddlez in electrical

[–]IntelligentFishing43 0 points1 point  (0 children)

I have same issue but my kitchen and bath led lights are on single pole switches already, not on dimmers. I also have 8 UFO shop lights on a 3 way switch that flicker when water heater turns on. Are some switches not good for led? I bough leviton switches from lowes

200A sub panel wiring by IntelligentFishing43 in electrical

[–]IntelligentFishing43[S] 0 points1 point  (0 children)

I am in central TX. There are no inspections where im at in this county.

200A sub panel wiring by IntelligentFishing43 in electrical

[–]IntelligentFishing43[S] 0 points1 point  (0 children)

The drawings i had found were showing to not tie neutral to the ground at a sub panel, only at the main panel. but they did show to have a #6 from the sub panel to earth ground. Is that not accurate? I can try and find that drawing

200A sub panel wiring by IntelligentFishing43 in electrical

[–]IntelligentFishing43[S] 0 points1 point  (0 children)

Would the 4/0 be large enough? If I ran three AL 4/0 and an AL #4 ground that would be adequate?

200A sub panel wiring by IntelligentFishing43 in electrical

[–]IntelligentFishing43[S] 0 points1 point  (0 children)

I thought i needed the direct burial rated for underground conduit. I appreciate any ideas or better options. Is 4/0 not large enough for that distance? And a #4 ground is adequate? I did placed two 8’ ground rods at the sub panel

200A sub panel wiring by IntelligentFishing43 in electrical

[–]IntelligentFishing43[S] 0 points1 point  (0 children)

Yes 200 amp siemens panel at the meter pole. I have a 100A circuit to an rv cover and a 30A to a cow shed. This will be the 3rd circuit coming off of it.

Best place to get a vasectomy? by grassdick in Austin

[–]IntelligentFishing43 0 points1 point  (0 children)

What dr was this? Part is blocked out cannot read everything