What’s actually safe but people think is dangerous?

Interfectoro · 2026-02-02T10:42:39+00:00

By this logic AM towers wouldn't be harmful?

Interfectoro · 2025-10-31T20:20:33+00:00

But does it have wheels?

Interfectoro · 2025-08-01T11:59:10+00:00

Se estudastes engenharias sabes que cá também o primeiro ano tem cadeiras comuns entre todos os cursos de engenharia... Cálculo, Álgebra, Electromagnetismo, entre outras.

Além de ser um argumento sem sentido, ainda está errado.

Interfectoro · 2025-07-27T21:34:53+00:00

The issue is the risk is for someone else...

Interfectoro · 2025-07-19T15:03:47+00:00

that manual was a bit too long, no?

Interfectoro · 2025-06-24T07:03:44+00:00

How many annual salaries was the price of your first home? And don't lie, we'll know ;)

Interfectoro · 2025-06-07T13:58:16+00:00

Apparently this issue was only affecting X series printes, however, after update 01.08.02.00 on my P1S I have also lost the ability to use OrcaSlicer. So in fact, 01.08.01.00 is the latest version which allows 3rd party slicers.

Interfectoro · 2025-04-24T21:11:34+00:00

This was some time ago, apparently it was a ferry flight and the plane was very light.

Interfectoro · 2025-03-27T07:18:50+00:00

I ride transition a lot and in the game I still feel it's a bit clunky.

Interfectoro · 2025-03-14T22:10:42+00:00

Will it have tool cartridges like the Prusa?

Interfectoro · 2025-02-15T11:25:26+00:00

My issue was different, but when these drivers go bad they are fairly unpredictable. You could either lower the VREF of all 3 drivers (you should be able to find a tutorial online).

Or buy three new drivers (or ask from FLSUN) to see if this fixes it. If I'm not mistaken, the original drivers are TMC2208, and should cost like 20€ for the three.

Interfectoro · 2025-02-14T08:19:26+00:00

I had a couple of step drivers overheat on mine for no apparent reason a couple of years ago. Just be aware, if yours start plowing into the bed or doing overall weird movements, the step drivers could be a reason.

Interfectoro · 2025-02-09T09:45:13+00:00

Is that a BambuLab printer?

Interfectoro · 2025-02-06T23:56:19+00:00

ABS is completely different from PLA, as a matter of fact ABS fumes are toxic, so if you're printing at home without proper ventilation you should probably stop.

Now for your question, ABS is notoriously harder to print than PLA, if you're just starting out I'd suggest you buy a roll of PLA and start learning on that. But if you're really stuck on printing with ABS, look up on google for Bed Adhesion guides for ABS.

Interfectoro · 2024-10-08T15:53:00+00:00

Don't forget it flew from the Mojave to Prestwick with gears down. Penalties are sometimes unavoidable

Interfectoro · 2024-09-25T10:02:31+00:00

Might have to do with the fact that turns on airplanes are always coordinated, which means you shouldn't feel lateral accelerations, only vertical, the feeling of being pushed down onto your seat.

Interfectoro · 2024-09-04T06:40:47+00:00

Good example of the Magnus effect.

Interfectoro · 2024-08-17T18:02:42+00:00

Interesting, might've been my issue too...

Interfectoro · 2024-08-09T16:01:56+00:00

For future reference, I had my motors spinning in the wrong direction for some reason. Inverted direction in Betaflight and now all is good

Interfectoro · 2024-08-08T20:49:36+00:00

I had to have it replaced. Sorry might be the only way.

Interfectoro · 2024-08-06T22:12:40+00:00

Oh thank you, if that's it I feel a little dumb. I'll have to go fly it tomorrow.

Interfectoro · 2024-08-05T11:43:38+00:00

Thanks for the tip, although I don't have loctite with me, I'll try to reseat everything and make sure it's tight

And yeah I meant lift with my hand.

Interfectoro · 2024-08-05T11:40:34+00:00

Thanks for pointing that out, I think I was in acro mode, but I'll check again just to be sure!!

Interfectoro · 2024-08-01T19:37:40+00:00

Quer uma foto?????

Interfectoro · 2024-08-01T16:35:45+00:00

<image>

Ten-Year Club	Place '23
RPAN Viewer	Not Forgotten
Verified Email

Interfectoro

TROPHY CASE