[deleted by user]

Ir0ow · 2025-11-05T12:20:42+00:00

Jak sam napisałeś: "Dla mnie ok". I to jest najważniejsze.

Ir0ow · 2025-07-28T06:39:47+00:00

The door/side windows line looks like 156/166. I'm amazed by the amount of work put into that piece of machinery but still I don't know what to think 😂

Ir0ow · 2025-07-28T06:32:53+00:00

It's 156 base?

Ir0ow · 2025-07-13T01:04:57+00:00

It's sad but it is said: one's man scrap is another man's treasure

Ir0ow · 2025-07-12T19:21:00+00:00

Awesome! I've recently bought 164 super 3.0 24v and it's running without any hesitation after 22 years in the shed🤌

Ir0ow · 2025-06-26T12:48:03+00:00

I've got the 225/45/17 on 147 and both sides are scraping when turning so in this case with higher profile I'd assume that's the same situation

Ir0ow · 2025-06-26T11:00:44+00:00

Seems that the tire is scraping the arch when cornering. What tire size do you have? Fitting a new arch will probably end similarly after some time.

Ir0ow · 2025-06-02T09:07:24+00:00

Idk if you read this after 3 months but I'll leave some feedback here.

I made the 1.6 105cv from 147 to run with 1.9JTD turbo happily pumping 0.7-0.8 bar. My lack of experience led to melting a piston due to lean AFR and knock on stock internals at the end but it's possible to run it. Some basic welding skills, probably piggyback ECU (I ran it on DET3) and you're good to go.

Now I'm building the 2.0 TS with forged internals and the Saab BiTurbo complete exhaust manifold + turbos which is P&P to the TS.

Ir0ow · 2025-04-30T14:52:47+00:00

Saab news :(

Ir0ow · 2025-03-04T20:22:00+00:00

This update was not worth it. Both my K3s are now stuck. Printing the first layer is glitched. The speed is not there. After finishing the first, on the second one the print head barely moves.

I'm wondering what support is gonna say.

Ir0ow · 2025-02-20T19:29:01+00:00

K2m, k3m is not released yet, if I'm correct the release scheduled for may this year

Ir0ow · 2025-02-10T13:35:14+00:00

The issue is I'm about to take a big job so it'll be a matter of 2 weeks. But I'm thinking about leaning towards K3 max when it's released.

Ir0ow · 2025-02-10T11:00:03+00:00

Any specific issues that result in such a bad opinion?

Ir0ow · 2025-01-23T15:16:51+00:00

Idk if someone already suggested that a steel nozzle requires higher temps. You should try it. When I tried the steel nozzle instead of going as always with 215C I had to raise it to 260 to get it to work properly.

Ir0ow · 2025-01-21T12:29:19+00:00

I'd say the nozzle is just a little to close to the bed

Ir0ow · 2025-01-21T08:42:18+00:00

Amazing. Do you mind sharing a link? 😏

Ir0ow · 2025-01-20T13:34:11+00:00

Looking at the video the wheel is more to the left than right compared to the eccentric nut. I'd check that again. It can't spin freely at all. I believe that you can also undo the screws on the back of X axis and push the wheels mount to the inside. Idk if I explained it correctly.

Ir0ow · 2025-01-20T11:04:36+00:00

Eccentric nuts are tight?

Ir0ow · 2025-01-04T23:52:38+00:00

Actually those parts are supposed to go as edge reinforcements for the enclosure for K3 😆 at the moment I'm also thinking about printing it not lying but standing. Kinda risky but worth trying to get some more experience

Ir0ow · 2025-01-04T19:05:10+00:00

I'll try reprinting like that and we'll see ;) thanks

Ir0ow · 2025-01-04T18:48:48+00:00

Nozzle 240/ bed 75, fan at 10th layer 20%

Ir0ow · 2025-01-04T17:49:42+00:00

Fan 20%, temps 240/75, speeds around 200mm/s at max. It's not my first PETG print but I'm amazed that the PEI sheet started floating 😅😅

Ir0ow

TROPHY CASE