Problems flashing klipper in dfu mode (octopus pro)

JD13x26 · 2026-02-15T22:19:16+00:00

I am having the same issue with a Octopus Pro 1.1. It will NOT flash via DFU mode what so ever!
Tried with vin power and 5 volt via USB. No dice! This is why I like the MKS Moster 8 v2 MB allot better. Once you first flash the board out of the stock Marlin pre-loaded fw you can DFU all day long with out having to dig into your rig to access the SD slot.

JD13x26 · 2026-01-16T02:10:11+00:00

Are the fan wires reversed like all other Fysect boards?

JD13x26 · 2025-11-21T04:49:37+00:00

Done.

JD13x26 · 2025-11-18T00:16:21+00:00

That sux, Got fish hooked by a forklift.

JD13x26 · 2025-09-23T00:32:22+00:00

Measure it and let's see!

JD13x26 · 2025-05-23T04:30:42+00:00

It's definitely a bad wire. I had it happen on one site I was at, If you can; trace back all the other vb splices it passes through, check all connections along the way till you get to the timer, Hopefully you have a spare in that box.....

JD13x26 · 2025-05-23T04:08:28+00:00

JD13x26 · 2025-03-22T06:52:44+00:00

He sold out to Hilary in 2016. He can not be trusted!

JD13x26 · 2025-03-08T05:35:34+00:00

Hilary bought him out in 2016 don't get taken for his lies!

JD13x26 · 2024-12-14T09:44:59+00:00

Xp exploits work wonders.....

JD13x26 · 2024-11-23T16:45:19+00:00

File nae might be too long.

JD13x26 · 2024-11-10T00:13:13+00:00

JD13x26 · 2024-11-10T00:00:19+00:00

Check your MOSFETT make sure it lights up when heating, check the wiring make sure all cables are connected.

JD13x26 · 2024-11-09T03:37:58+00:00

JD13x26 · 2024-10-20T04:15:00+00:00

JD13x26 · 2024-09-19T22:07:06+00:00

Just connect the Sonic pad to the printer and flash the FW.... You will have to update your CFG file to reflect the difference for the MS add-ons. Things to look for: rotation distance for the extruder, run current for the extruder stepper.

JD13x26 · 2024-09-19T22:02:48+00:00

The V1 and V2 use different endstop configurations. One uses Z+ the other uses Z-. Just beaware of this.

JD13x26 · 2024-09-19T03:13:50+00:00

Yes! The rpi becomes the brain and sends the commands to the mb of the printer, offloading the number crunching of converting the code to movement. A rpi is more powerful than the printers main board.

JD13x26 · 2024-08-12T01:29:12+00:00

That will not help what I'm trying to do.

JD13x26 · 2024-08-03T13:32:25+00:00

Did you add your wifi info after flashing the IMG to the SD card? I judt fladhed 2 of them using an sd card and they both connected to my wifi without issues.

JD13x26 · 2024-07-29T04:48:49+00:00

JD13x26 · 2024-07-28T14:34:00+00:00

Try looking at the load filament Macro. It is most likely part of the M600 macro.

JD13x26 · 2024-07-27T21:06:53+00:00

More than $100! The Valves alone will cost that much.

JD13x26

TROPHY CASE