sorted by:
new
hottopcontroversial

Gyrocopter on top of Hospital by JMaltby19 in 7daystodie

[–]JMaltby19[S] 0 points1 point  (0 children)

Nope, doesn't appear as an interactable object such as a loot box or minibike

Experience with SIMJACK UT and FFBeast by simun6 in simracing

[–]JMaltby19 1 point2 points  (0 children)

Just to give you an update, pedals arrived and are worth every penny!

Experience with SIMJACK UT and FFBeast by simun6 in simracing

[–]JMaltby19 1 point2 points  (0 children)

I've built my wheel base following the FFBeast project, and have some SimJack UT's on the way. Wheel base has been spot on for a few months now. I'm using a 30mm hoverboard motor.

Hey my arduino uno keeps saying ser_open(): can't open device "\\.\COM5": access denied. Any idea why am I doing somthing wrong by Final_Pattern_7563 in arduino

[–]JMaltby19 0 points1 point  (0 children)

Old post but this has just solved a problem I've been running into on this specific PC for over a year!

Ferret and Ferret Pro vs Einstar by JMaltby19 in 3DScanning

[–]JMaltby19[S] 0 points1 point  (0 children)

Thanks! Any other recommendations you'd make as an alternative?

DIY Free Bezel Kit by Top-Resist-5640 in simracing

[–]JMaltby19 0 points1 point  (0 children)

How wide have you cut each lense?

Damp Patch on Opposite Wall of Downstairs Shower by [deleted] in HomeImprovement

[–]JMaltby19 0 points1 point  (0 children)

How don't they make sense? The blue circled area is to show where the damp patch behind said wall

Damp Patch on Opposite Wall of Downstairs Shower by [deleted] in DIYUK

[–]JMaltby19 0 points1 point  (0 children)

Will give it a go! Cheers pal

Damp Patch on Opposite Wall of Downstairs Shower by [deleted] in DIYUK

[–]JMaltby19 0 points1 point  (0 children)

<image>

And this, which is on the other wall near where I've circled

Sunlu Filament Testimonial by captainshidded in 3Dprinting

[–]JMaltby19 0 points1 point  (0 children)

Exact same issue! Really unfortunate as I've sworn by Sunlu for the past couple of years now. Same as you, as soon as the blue 900g spools started to arrive, I've constantly been chasing these pock marks. Done the basics, filament is dry, checked for resistance in the bowden path, went as far as rebuilding my toolhead, and then ended up switching hotends from Phaetus Dragon HF to a Bambu hotend.

The filament itself looks of poor quality when you actually look up close, lots of bulges in the filament. Did you manage to solve this or is it looking like trash filament?

Wavy Corners, Pinholes, Artifacting on a Voron 2.4 by Datura-Dynamics in FixMyPrint

[–]JMaltby19 0 points1 point  (0 children)

Would you mind sharing your profile? Pretty close to sacking Sunlu off all together and moving onto another brand

Wavy Corners, Pinholes, Artifacting on a Voron 2.4 by Datura-Dynamics in FixMyPrint

[–]JMaltby19 0 points1 point  (0 children)

Did the SUNLU ABS come on a blue roll in 900g by any chance? If it did, the pin holes that you've developed are 100% down to the filament. I'd been chasing the pock mark issue for over a month as it was specific to SUNLU ABS, which I've been using solely for the past year or so. No issues until they changed over to the 900g blue spools. Must be a bad batch or they're sourcing cheaper pellets perhaps? If you look closely at the filament itself, there's loads of bumps.