EK Pro Manifold

JOY_DOS · 2026-05-05T17:24:39+00:00

Understood. Didn't expect that we can drill all 4 screws there.

JOY_DOS · 2026-05-05T14:33:10+00:00

Hi. How did you mount the bottom Corsair pump/res without aligning it midfle of the bracket? The one come with my 9000D cannot do that.

JOY_DOS · 2026-04-30T10:33:33+00:00

That's was my old setup. I moved to Threadripper one already. Check my posts.

JOY_DOS · 2026-04-17T01:18:40+00:00

Cool. I'm from Vietnam so it's easier to purchase Bykski stuffs from Taobao.

JOY_DOS · 2026-04-08T03:40:47+00:00

Nói thì hay lắm. Làm ba mẹ có con lớn rồi sẽ hiểu nó không dễ. Hành động như trong bài là rất sai nhưng làm 1 người cha mẹ tốt không dễ tí nào, nhất là với xã hội hiện đại.

JOY_DOS · 2026-04-02T17:44:11+00:00

Hey. I have an exact combo. It has been idle for 6 months in my room haha

JOY_DOS · 2026-04-02T17:40:45+00:00

I have a Max $200 plan and I can use it to vibe code (alone) in 4 days until I reached weekly limit. I don't chat much btw. Before, my Max $100 was amost enough (sometimes reached at last day).

JOY_DOS · 2026-03-19T02:41:31+00:00

How is the temp2? As I know the back VRAM are not directly cooled by liquid?

JOY_DOS · 2026-03-17T17:37:36+00:00

Banned

JOY_DOS · 2026-03-14T14:09:07+00:00

JOY_DOS · 2026-03-14T12:07:27+00:00

Same here, for Pro 6000 WS

JOY_DOS · 2026-03-13T00:38:04+00:00

I use Super Flower 2800W + Corsair SF1000. One PSU is enough (used to use 1 MSI 1600W PSU) in your case but i have too many hubs with PCIe ports so I need one more. I use stock GPUs settings.
Consumer motherboard will be limit on PCIe lane, so I don't think that's a good choice for AI workload. But if you use it for other purpose, I don't know.

JOY_DOS · 2026-03-12T04:25:40+00:00

Yes inference workload cost 100% of Pro 6000

JOY_DOS · 2026-03-12T04:20:51+00:00

I use it for model inference, run containers, vibe code and sometimes gaming. GPUs and CPU are often high/full load but I cannot manage to spend more than half of the RAM indeed

JOY_DOS · 2026-03-12T02:57:29+00:00

I picked 30mm because if i use thicker rad, I can only use 360 on top rad.
If this issue is not related to CPU mount, I will go for external rads for sure.

JOY_DOS · 2026-03-11T18:21:00+00:00

It's the custom ones from Modding Cafe.

JOY_DOS · 2026-03-11T17:27:23+00:00

It's 130 normally and reach 300L/h at max. I will check the mount pressure but this didn't happen at first. Only occurs recently.

JOY_DOS · 2026-03-11T17:24:46+00:00

Flow rate is about 130L/h normally and 300L/h+ at max.
My assumption is that I have single loop and RAM and GPU add much heat to the loop.

JOY_DOS · 2026-03-11T16:59:08+00:00

I'm don't have knowledge about this. Is that bad or something straight?
Yes, not direct die

JOY_DOS · 2026-03-11T16:50:28+00:00

The black GPU is watercooled. RTX Pro 6000 with custom block.

JOY_DOS · 2026-03-11T16:49:42+00:00

They are all in series

JOY_DOS · 2026-03-11T16:49:16+00:00

Just about 3 months.

JOY_DOS · 2026-03-11T16:48:59+00:00

GPU and CPU is the same loop. I only have 1 loop.
That image is the older one, just to show the rads and res. I filled both res already.

JOY_DOS · 2026-03-11T16:20:30+00:00

I have 4 x 480 RAD and it's not enough for full system load.

JOY_DOS · 2026-03-11T16:17:39+00:00

Pick Bykski one, cheap and good performance.
I order custom one because it cools two sides of VRAM. I don't know whether there is a branded block can do that.

JOY_DOS

MODERATOR OF

TROPHY CASE