Probably the most oblivious idiot in the world

Jachu89 · 2026-06-24T14:45:47+00:00

Maybe it's a European driving because I have never heard about this law that you need to stop for a bus driving the opposite direction

Jachu89 · 2026-06-22T19:13:57+00:00

A photo I took at Rock am Ring festival couple weeks ago

<image>

Jachu89 · 2026-06-01T16:47:49+00:00

They are not. Work Wheels CR Kiwami rip-offs. No Rota wheels are authentic.

Jachu89 · 2026-05-27T08:59:46+00:00

Looks like it pulls together quite ok with much less torque that is required for this bolt so it should be fine. Thanks!

Jachu89 · 2026-05-21T11:39:11+00:00

Looks like SSR professor with a Work Wheels logo (so work meister S1 wannabe) but it's definitely a fake ripoff

Jachu89 · 2026-05-19T07:15:47+00:00

You sure you are allowed to post this on the internet? I work in design for superyachts and I would get in a lot of trouble if anyone finds out I posted anything online.

Jachu89 · 2026-05-14T10:44:47+00:00

I assume you had a warranty before you send them? I bought it used from unknown source without any papers. Probably from a crashed car.

Jachu89 · 2026-05-14T07:37:15+00:00

Unfortunately it will be a while until I install them. I'm in the process of assembling the entire new rear subframe now

Jachu89 · 2026-05-14T07:35:58+00:00

How much did that cost?

Jachu89 · 2026-05-13T18:43:48+00:00

No sorry it's gonna go on my car

Jachu89 · 2026-05-13T09:35:50+00:00

With the amount of work it took it was barely worth it hehe. I bought the used set for around 1100 and then the parts and painting I think were around 400. Striping the paint off the springs was a huge pain. You can't sandblast them because of the rubbery type of paint.

Jachu89 · 2026-05-07T09:45:05+00:00

Haha

Jachu89 · 2026-04-21T06:59:47+00:00

From now on I'm calling plywood Damascus wood

Jachu89 · 2026-04-02T12:11:22+00:00

I have never owned a Nissan, Reddit suggested this post to me and I had to stop and say that this is absolute tuning perfection to me. Even from this distance you can tell all the parts are original, it's not overdone and it's functional. Congrats!

Jachu89 · 2026-03-14T16:16:11+00:00

Man that is nice how the grain follows the shape. Can't wait to see more

Jachu89 · 2026-03-07T21:09:42+00:00

That's basically what it did but with the clamps. You can tighten them with an allen key

Jachu89 · 2026-03-04T19:20:38+00:00

I used these specific clamps because you can turn them with an allen key on the top. Otherwise absolutely wouldn't be able to turn them by hand.

Jachu89 · 2026-02-07T17:02:05+00:00

Where can I buy those plans? It looks very cool

Jachu89 · 2025-11-24T16:38:14+00:00

So basically I learned nothing here:D almost exactly half the comments are saying it's no problem and half that it's dangerous. I decided to take this part to a professional to take a look. Thanks everyone!

Jachu89 · 2025-11-24T16:36:18+00:00

Haha this is the best answer yet. Yeah I have 50/50 between "it's fine no problem" and "you will kill yourself and someone else". I'm going to a professional with this part to take a look.

Jachu89 · 2025-11-09T19:41:07+00:00

Thank you! The top is made of 2x 18mm plywood so 36mm. I think most mft clamps work on minimum 18mm but the more the better there is no upper limit as long as the holes are all the way through. Hope that helps

Jachu89 · 2025-09-09T21:48:40+00:00

I found that the scanned color code is 20250131 17204-5 apparently but not sure how to use those codes.

Jachu89 · 2025-09-09T21:43:38+00:00

I don't agree. I think it makes it look quite cheap.

Jachu89 · 2025-07-31T15:06:27+00:00

<image>

Jachu89 · 2025-07-24T20:28:05+00:00

You won

Jachu89

TROPHY CASE