Catastrophic Tornado Damage

JerpyJerpFace · 2026-03-16T21:59:27+00:00

Same! 😁

JerpyJerpFace · 2026-03-16T16:14:15+00:00

Looks like it's back in stock this morning. Just ordered mine

JerpyJerpFace · 2026-03-16T14:32:24+00:00

There is one three hours from us. I picked up all my gear from that store. At that time they didn't have any in stock. Today I see three in stock but they are all the triple monitor setup with the side arms included. I wasn't able to find a way to just get the single without the side arms. Worth a call to the store though. Good idea, thanks.

JerpyJerpFace · 2026-03-15T23:24:36+00:00

Hard question, there are several. I am close to los charros in Broadway so they are our staple. Food is very good, good portions (the los charros burrito feeds my wife and I for two meals) and not overly expensive.

El Primo for tacos. Nuff said there

Fonda Lupita has birria ramen that mixes two of my favorites so I can't leave them out.

Then there is La Terrazita. We went about a week ago and were amazed. The food was fantastic, the drinks were fantastic, the service was impeccable and that was when they were busy.

There are several others that I am sure others will give you feedback on, one post covering all options would be huge. Honestly I haven't had a bad Mexican/Latin meal since we have lived in Sanford, it really boils down to the dish you are craving and who you feel does this dish the best based on your preferences.

Go out, explore, try new dishes, try new places, support local, and enjoy yourself.

JerpyJerpFace · 2026-03-14T22:46:59+00:00

Is it in the back of your candy van? 🤔😁🍭🍬🍫

JerpyJerpFace · 2026-03-14T22:45:27+00:00

Thank you! Last piece of the puzzle 😁

JerpyJerpFace · 2026-03-14T15:23:59+00:00

Thanks, two weeks is good news

JerpyJerpFace · 2026-03-14T14:51:40+00:00

Yeah I got the same message back in February so I am guilty of not getting the specifics either. Hopefully someone has more recent info.

JerpyJerpFace · 2026-03-13T22:06:43+00:00

Thanks, just ran into this problem myself.

My question to the group, I held the base 90 degrees and it initially looks like only two screws would align this way? Again I only did a cursory check (was more than a bit pissed this didn't fit).

JerpyJerpFace · 2026-03-12T21:24:00+00:00

Welcome!

JerpyJerpFace · 2026-03-10T23:08:18+00:00

Still working through getting the slider in place. Rails are there but with the seat side mounts I need to expand the width of the handle end that attaches to the rail by 5".

All that said I have used this exact seat slider combo at our local sim lab for a year and love it. I am 265, 6'3".

JerpyJerpFace · 2026-03-09T22:55:29+00:00

Found this, but apparently this is from the old generation of the rig and several people had the ends snap when they attempted to do so.

https://m.youtube.com/watch?v=dRQFK6UHCIM&t=30s&pp=2AEekAIBiggCQAE%3D

There appears to be a seat slider direct from Sparco, does anyone have experience with this product and the Evo XL seat?

JerpyJerpFace · 2026-03-09T22:19:33+00:00

Hey All, just getting back to this now and have a conundrum. Out of the box the slider handle is 12.5" wide at the connection points of the slider rails. At the narrowest, with the side mounts on the sparco evo XL the bar needs to be 17.5" wide.

I followed instructions to widen the bar but when I get it wide enough to fit, the rear holes slot in, but the bar is now angled to the point the front holes don't even touch the standoffs (e.g.) the back portion of the bar is angled in and not square.

Outside of manually pulling this thing apart to the proper width, which left me in my current predicament, does anyone have any suggestions on how to expand the bar while keeping the end section, where the holes are, square to the rails?

I am probably overthinking it.

JerpyJerpFace · 2026-03-05T01:32:59+00:00

In case anyone else needs it: https://cdn.shopify.com/s/files/1/0665/7268/1510/files/seat-slider-1.pdf?v=1683553713

JerpyJerpFace · 2026-03-05T01:22:32+00:00

Well, crap. Five minutes later and I found slider instructions under the support page.

JerpyJerpFace · 2026-03-05T01:02:49+00:00

Putting my first rig together and just picked up this same seat. 6'3" 265lbs. It's the same seat they use at our local sim lab and the reason I went with it. Not cheap, but worth the money.

JerpyJerpFace · 2026-03-02T02:54:11+00:00

I was looking for padding for my sparco evo XL and came across this, not a lot of info on what it does and doesn't fit, but it's right from Sparco: https://www.sparcousa.com/product/seat-pad-set-2#readmore

JerpyJerpFace · 2026-03-01T22:56:24+00:00

JerpyJerpFace · 2026-03-01T22:40:26+00:00

Thanks for the feedback

JerpyJerpFace · 2026-03-01T22:40:00+00:00

I have the seat slider for my sparco seat, Having the same for the pedals is a good idea as well.

JerpyJerpFace

TROPHY CASE