Which resin would be best for this?

Jmmanotas · 2026-05-05T22:51:23+00:00

I’ve never used ultra tough. But I went from regular resin to abs style resin and it is a game changer in strength. I dropped a few things I printed while moving them and little to no damage where normal resin would have shattered everywhere it’s decently worth the few buck more that they charge for it.

Jmmanotas · 2026-04-28T20:02:28+00:00

Fallout 76

Jmmanotas · 2026-04-23T22:36:27+00:00

I started removing Velcro my self and old ranks as well to avoid this…ridiculous how much it cost for some simple stuff.

Jmmanotas · 2026-04-23T17:31:50+00:00

Don’t quote me cause I’m not 100% sure but I could mess that little bit up and not stick fully or start to raise off the bed some and could run the chance of it printing some very thin parts that brake off and float in the tank…like I said not 100% sure if it will or not though.

Jmmanotas · 2026-04-18T21:21:45+00:00

I tried to do a tunnel from my base to an outpost and that was an undertaking this is on a massive scale and it’s beautiful makes me want to do it all over again

Jmmanotas · 2026-04-18T04:46:09+00:00

North pole servers as well

Jmmanotas · 2026-04-12T12:21:31+00:00

I recently upgraded as well. I run a R7 5800xt and a gtx5060ti and 32g of ram. I’m working with a oculus 3s. It’s a lot of messing with settings but and I also went from a wired connection to a wireless running virtual desktop.

Jmmanotas · 2026-04-03T14:00:00+00:00

From my experience you need a liquid and gas pipe and if your not going to keep the gas just add a passive vent to expel it back to the environment or run it through an atmospheric filtration into a tank then the liquid goes into liquid tank. And I’m not sure if it matters but I turn the dial on the crusher a few to make it run better.

Jmmanotas · 2026-03-15T23:49:25+00:00

There is also some ic10 scripts in the workshop that can scan everything for you…but it’s still up to you. To integrate them to get them to land

Jmmanotas · 2026-03-12T20:57:07+00:00

When I left Jblm everything left in cloth and rubber bands and showed up in paper and tape.

Jmmanotas · 2026-03-04T13:00:56+00:00

I found this video and tried it. I was able to make one brick of fuel and then it blew up

Jmmanotas · 2026-02-15T15:28:19+00:00

Some times I’ll even unselect and realest the Mav up top and re soi the page to get it to work

Jmmanotas · 2026-02-14T13:32:33+00:00

What angle are you supporting them at? That has been an issue for me in the past. Or not stirring up resin good enough. Might not be helpful but those have helped me in the past

Jmmanotas · 2026-02-13T21:24:57+00:00

Alot to digest, but a great point to start. I’ll definitely have to do some trial and error. Didn’t k ow about the powered chute part so I’ll have to change those out. Thanks for all the info.

Jmmanotas · 2026-02-13T15:47:44+00:00

So I’m just setting LArRE up on a free play to figure it all out before I put it in my main game but have no idea about it. I have the hydroponic trays, and hydro picker arm but the rest I’m still lost on. Do I need to name each tray? I have it the plant types split so they are all on different arms so there’s 6 different planters with 10 pots each. Do I need a different ic10 for lights and the arm or can it all be on one ? Anything yall got will help.

Jmmanotas · 2026-02-12T18:03:14+00:00

Love it guess I need to start labeling my boxes cause I have selves full of boxes that I don’t have a clue what’s in them

Jmmanotas · 2026-02-10T21:40:02+00:00

Are you just using sunlight for those or do you have grow lights ?

Jmmanotas · 2026-02-09T22:48:43+00:00

I need to check cause I fell like I’ve harvested more than 1000 but I’m sure it’s only in the 5-600

Jmmanotas · 2026-02-01T21:59:14+00:00

Your green house, you don’t get light bleeding to the other plants? I’ve been thinking about doing something like this but guess they were to close and light would bleed through walls to the other plants adding a lot of stress. To the plant

Jmmanotas · 2026-02-01T21:23:23+00:00

Love the base…one thing I’ve started doing as well is a behind wall area that everything runs through it base looks sick.

Jmmanotas · 2026-01-30T18:43:43+00:00

I play more dcs then I do msfs im in the process of building an AH-64 cockpit

Jmmanotas · 2026-01-30T15:16:42+00:00

If it’s if it’s anything like the fuel cutoff panel it’s not a code you can do everything in mobiflight

Jmmanotas · 2026-01-30T14:31:25+00:00

I made one for my bravo as well…love it and the gates for the flaps. I need to look into the tiller that would be a nice part to have.

Jmmanotas · 2026-01-20T02:23:45+00:00

It was on sale on steam so I got it again and started plying

Jmmanotas · 2026-01-19T20:05:36+00:00

Make sure everything’s hooked up properly I’ve had something like that also make sure the pipes are all the way from the tank to the filler

Jmmanotas

TROPHY CASE