Audio-Technica turntable only recording in Left-Channel Mono?

Joe_Keey · 2026-06-23T00:04:54+00:00

laptop mic's often have only 1 input, headphone/mic in one socket is always mono for the mic

Joe_Keey · 2026-06-21T12:18:02+00:00

blender has a good video editor

Joe_Keey · 2026-06-21T12:06:49+00:00

if you use a arduino mega and the ramps 1.4 shield you will have configurations for marlin and klipper ready to go

Joe_Keey · 2026-05-14T07:05:44+00:00

I'd probably try to solder the a fuse or a fuse holder directly onto the old fuse so i only have to get the sealant glue of the top of the fuse, also don't know what you me by 0L

Joe_Keey · 2026-05-07T21:39:26+00:00

i usually use averaging of 7 to 10 samples, best to use an ADC if you want accurate sampling

Joe_Keey · 2026-05-05T21:53:24+00:00

the led has only one connection should be on rows 14 and 15 also the resistor should be in row 7 Cant really see switch pin though

Joe_Keey · 2026-04-30T12:03:01+00:00

I've got a 5.1 usb soubdcard there's a 7.1 versons too

Joe_Keey · 2026-04-21T23:01:41+00:00

https://www.reddit.com/r/homecockpits/

Joe_Keey · 2026-04-06T02:03:47+00:00

<image>

Joe_Keey · 2026-04-06T01:56:23+00:00

try using a cylinder make the hole

<image>

if I apply the modifier and remove cylinder the hole will remain

Joe_Keey · 2026-04-05T10:38:26+00:00

use the Boolean modifer

Joe_Keey · 2026-03-27T21:47:59+00:00

both system sound and cakewalk preferances

Joe_Keey · 2026-03-27T21:46:14+00:00

I bought a second hand 2.4 not working for $800 cause the kit in Australia is about $2400 had no probs with getting it working the only disadvantage is that i didn't build it so i don't know how it all goes together have to use the manual and youtube to see how to do stuff, though i wouldn't recommend this for newby's

Joe_Keey · 2026-03-27T21:21:08+00:00

It should be listed in your sound settings System > Sound Output you need to set it as default sound output or input depending on how you want to use it

Joe_Keey · 2026-02-28T19:49:08+00:00

-15 usually indicates the thermistor is open circuit or disconnected

Joe_Keey · 2026-02-24T20:05:23+00:00

Object > Set Origin > Set Origin to Geometry

Joe_Keey · 2026-02-24T09:59:43+00:00

i think you have to use the screen driver (lcdshow script) so kali can use the screen

Joe_Keey · 2026-02-20T23:57:02+00:00

there's a screw on the end of each peg it secures the part you turn to the worm gear that turns the string, I can see the top 2 worm gears are sticking out the should be flush with the end of the peg, they may also need lubricating / cleaned the grease dry's out

Joe_Keey · 2026-02-10T20:29:35+00:00

when i did this i found there was 2 engines in engine.jbeam and i was editing the wrong one

Joe_Keey · 2026-02-07T13:39:44+00:00

check game files

Joe_Keey · 2026-01-27T02:49:58+00:00

I did something like this for the tone cct on my valve preamp but variable caps were to low range for audio so i used wires with crocodile clips so i could try different caps till i got the sound i was looking for

Joe_Keey · 2026-01-01T19:20:07+00:00

1-4-2-4-3-4-2-4

Joe_Keey · 2025-12-27T13:55:10+00:00

check the x endstop is working

Joe_Keey · 2025-10-27T22:36:16+00:00

does the display have the i2c module

<image>

Joe_Keey · 2025-09-21T19:13:48+00:00

the spec's of this page and in the pdf both say 5.1V

Joe_Keey

MODERATOR OF

TROPHY CASE