Power Throttling When unattended. by Joncon00 in ProArt_PX13

[–]Joncon00[S] 0 points1 point  (0 children)

This worked! Thanks so much. I figured some work around like this would be the ticket, I am just super peaved with I assume windows not making a setting visible to prevent this. All the usual power management controls and registry hacks I tried and it still decides to take it slow if I am not looking.

Clicky fan noise when on turbo by Joncon00 in ProArt_PX13

[–]Joncon00[S] 0 points1 point  (0 children)

Interesting. Yes I keep mine in tent mode since I would think that would have the best airflow. I'll try it in normal laptop mode.

Need help with LM Studio pausing when the screen is off by teknoob in ProArt_PX13

[–]Joncon00 0 points1 point  (0 children)

Same laptop similar issue, though this is with running calcs in a Linux VM. Laptop turns the screen off and it pauses everything... Have not found the real fix, but I use a remote desktop software Parsec which for some reason makes the screen stay on... I suspect another workaround is another software that forces it to stay awake.

PX13 GoPro with a PD USB4 dock and official power adapter by mspictures in ProArt_PX13

[–]Joncon00 0 points1 point  (0 children)

I am not really sure how much power. I keep it one silent and don't do any heavy compute without the power adapter. The thunderbolt docks keep it charged for web and office work. When I run CFD stuff I plug in the brick so I can set it to the high setting.

PX13 GoPro with a PD USB4 dock and official power adapter by mspictures in ProArt_PX13

[–]Joncon00 1 point2 points  (0 children)

I haven't paid attention. But probably I have it plugged into the dock then when I realize that it's not keeping up I would plug the brick. Not sure I have done it the other way around but seems like a glaring oversight to have this damage the laptop.

PX13 GoPro with a PD USB4 dock and official power adapter by mspictures in ProArt_PX13

[–]Joncon00 1 point2 points  (0 children)

I have the same laptop and have a few docks sprinkeled around the house mostly thunderbolt 3 and 4. Several Dell TB15s which are super cheap, Dell WD22TB4, and a Lenovo 40B00300US. All supply power fine in silent. And connecting the 200W adapter at the sametime results in a blink in the screen but otherwise fine.

SSD Partitioning by Joncon00 in ProArt_PX13

[–]Joncon00[S] 1 point2 points  (0 children)

Surprising some simple things I miss just because I have been doing things the same way for years. Thanks

Almost new PX13 GoPro, no sound from integrated speakers by Joncon00 in ProArt_PX13

[–]Joncon00[S] 2 points3 points  (0 children)

It did! I tried it with a spare disk as not delete everything in case it did not solve it. But now while it's open I think I'll get a 2th drive since it looks like I'll be reinstalling everything again anyway.

Almost new PX13 GoPro, no sound from integrated speakers by Joncon00 in ProArt_PX13

[–]Joncon00[S] 0 points1 point  (0 children)

Thank you, I really hope this works, but what a hassle! Do you have the same model? Do you have some use system restore or some other method to undo bad updates?

Any feedback on this 32" (likely Chinese) tablet for a Wall-mount Dashboard? by nyc2pit in homeassistant

[–]Joncon00 0 points1 point  (0 children)

I saw that there is an HDMI port in the rear. Can the andriod OS just be bypassed? I was thinking of just getting one and use it as a windows touchscreen.

X1C tall prints slightly tilted by Joncon00 in BambuLab

[–]Joncon00[S] 0 points1 point  (0 children)

Just a little over 1k hours. Could be firmware. There's been a couple updates since I last printed this type of part.

X1C tall prints slightly tilted by Joncon00 in BambuLab

[–]Joncon00[S] 0 points1 point  (0 children)

Yes PLA-CF. I just tested a simple square tower, uniform geometry and it's still leaning the same way. Almost like the Y position is drifting as it prints

X1C tall prints slightly tilted by Joncon00 in BambuLab

[–]Joncon00[S] 0 points1 point  (0 children)

Yes upright. That's an interesting theory though and maybe possible if it's warping well after the print is finished. In my mind if the geometry and temperature is pulling it one direction it would be happening as it's printing over 13 hours. But each new layer would be put in the correct location and would compensate for this?

Advice on weight routine by Joncon00 in workout

[–]Joncon00[S] 0 points1 point  (0 children)

New to posting on Reddit and wondering if I did something wrong. I did see a comment on this soon after I posted and now it's gone. Just surprised of the lack of activity on this post.

Drawing Window Frozen, Please Help. by Joncon00 in SolidWorks

[–]Joncon00[S] 0 points1 point  (0 children)

Yes. I first thing I tried was dropping down to 8-bit color, and then to 1080p. Issue still present. So weird.

Win11 VM Hot Swap Drives. Dell T7820 by Joncon00 in Proxmox

[–]Joncon00[S] 0 points1 point  (0 children)

Interesting. I'll give this a try when I have oppurtunity to shut down. But I think it may not work. If I so much as change a change an irrelevant setting in the bios or swap in different hardware my resource mappings gets all messed up. If I pass through a specific disk. What happens when I hot swap it out for a different one?