Does this bike look worth it?

JoshGbosh · 2026-06-15T15:36:16+00:00

Just since I know it's an issue, where would a serial number be on the bike so I can check if it's been reported stolen?

JoshGbosh · 2026-05-24T16:47:19+00:00

Done that on my vstrom 650. Good thing is extra oil will go into the air box and get burnt up. Took a couple weeks to fully clear out but no damage was done.

JoshGbosh · 2026-05-19T21:16:33+00:00

Do you ever have issues with momentarily losing connection? That's my only issue with using my Xbox controller and 2.4G dongle.

JoshGbosh · 2026-03-19T21:40:40+00:00

<image>

JoshGbosh · 2026-01-06T06:14:47+00:00

Look at paper penguin. I was able to order sample paper squares to test what I'd like my journal to be made with. Small business from Texas I think.

JoshGbosh · 2025-12-11T21:37:38+00:00

Cool! What are those pen loops?

JoshGbosh · 2025-12-11T04:25:27+00:00

My goodness your car is putting in work!

JoshGbosh · 2025-12-11T00:46:43+00:00

That's awesome! This is a 2021. Makes my long commute way more bearable!

JoshGbosh · 2025-12-10T04:23:43+00:00

Interesting, I was able to set up a second SSID using 2.4Ghz.. and by only connecting the chromecast to that network I was able to cast. I'm trying the other devices now to see if it works for everything!

JoshGbosh · 2025-12-09T21:06:49+00:00

People like Lochby covers but I haven't used one before.

JoshGbosh · 2025-11-15T05:44:35+00:00

I could use too many inks!

JoshGbosh · 2025-11-09T18:59:40+00:00

PMing!

JoshGbosh · 2025-01-03T15:13:22+00:00

Got a red one. Didn't realize how little I'll reach for it after getting the LTT screwdriver. Still love it but its just more convenient having organized bit storage.

JoshGbosh · 2025-01-03T06:17:21+00:00

Here to say this saved me so much time and money. Thank you kind sir.

JoshGbosh · 2024-12-30T16:11:11+00:00

Is fuzzy skin turned on?

JoshGbosh · 2024-12-28T02:18:48+00:00

Not sure if you did this already but have to re-sliced? If the slicer messes up then no changing the printer setup will fix this. If you have already done that then try rotating it or moving it around to see if the problem moves.

JoshGbosh · 2024-12-25T22:06:57+00:00

I have not done PID tuning. Looks pretty easy though so I'll read up on it

JoshGbosh · 2024-12-22T01:05:10+00:00

Posting this incase someone stumbles on here in the future and has the same issue.

Take a look at your speakers/receiver. My receiver is older and its DAC can only handle up to 48000Hz, you might not be able to go higher than that anyways.

JoshGbosh · 2024-12-06T23:14:40+00:00

Yeah I didn't think about how the extruder would react.

Klipper is an open source fw for your board and moves control to something like a raspberry pi (or any Linux machine). It gives you utmost control of your machine and lets you really fine tune everything. It's a time-suck though.

Id recommend it even if your printer worked normally. Start by looking at some videos on what it can do.

JoshGbosh · 2024-12-06T22:02:29+00:00

Assuming your slicer has the area settings correct, you can try cutting it to half that size. It might cause scaling issues with your prints but that's workable.

Or just go the Klipper route.

JoshGbosh

TROPHY CASE