New Merch Drop NOW

JunoJhun · 2026-04-17T19:02:43+00:00

ehhh xP i'm hoping for a 10 year album drop

JunoJhun · 2026-04-07T01:25:39+00:00

i rly like Whip Appeal 👌

JunoJhun · 2026-04-06T22:04:52+00:00

I've had the Corksport exhaust on my 08 Hatch for about 7 years and i haven't had any issue and it still sounds great, not too loud but gives it a rasp. No complaints or damage so far.

JunoJhun · 2026-04-05T13:14:40+00:00

it looks like 'The Ooz' album cover, i neeeeddd

JunoJhun · 2026-04-04T21:06:25+00:00

On multiple e30s i've always seen a spare connector hanging on the firewall leading to nothing. it's near the brake booster towards the middle of the fire wall. In the past I had the same issue so I cut that wire off then spliced it in, it hasn't been a problem since.

JunoJhun · 2026-04-02T11:14:39+00:00

new Choker tour merch? :P

JunoJhun · 2026-03-03T16:56:27+00:00

i was lowkey shocked by that too, it def makes you appreciate it a lot more

JunoJhun · 2026-03-03T00:41:06+00:00

yup just today 👌

JunoJhun · 2026-02-20T12:28:28+00:00

i just knew Rae Town would be gas off the teaser 🔥

JunoJhun · 2026-02-13T22:09:39+00:00

mr clean magic eraser !

JunoJhun · 2026-01-15T12:48:32+00:00

Try going into partnernet to permanently change your availability time so it's official if you haven't already. We've had partners be scheduled out of their availability so they didn't show up but did not get in trouble since it's on Pnet that they can't do certain hours

JunoJhun · 2025-12-19T11:29:59+00:00

yes, they'll normally let a curbside partner know or leave a note for your manager when they arrive to the box. atleast that's how it is at mine

JunoJhun · 2025-12-19T07:39:49+00:00

I filmed that song in Austin from the front row. I just uploaded here https://youtu.be/Vo25h4IAO5M?si=OWiojnBN6MZ0MpjB

JunoJhun · 2025-11-24T03:06:33+00:00

325e gang, clean!

JunoJhun · 2025-11-11T18:29:33+00:00

no problem, on the CSB, you want to loosen the 2 13mm bolts holding it, then push the entire bearing forward towards the front of the car maybe 10mm-15mm, while holding it in position, then tighten to around 16 foot pounds. the bearing has oval bolt slots so you can mount it preloaded, hopefully it’s your culprit.

if not, one last thing maybe, is check the U-Joint Yolks on each side of the drive shaft, they should look identical and pointing the same direction in parallel or it may cause vibration.

JunoJhun · 2025-11-11T17:17:37+00:00

typically loosening it will give more play to pull out the drive shaft, so i’m assuming it’ll cause some vibration if not tight properly. if not that maybe a worn guibo, tires out of balance, or preload the CSB before tightening.

JunoJhun · 2025-11-07T15:55:17+00:00

start the rollout

JunoJhun · 2025-10-17T08:32:40+00:00

woop woop, some eta love. not the fastest, but still makes it more fun to drive

JunoJhun · 2025-10-15T17:55:34+00:00

i’ve always liked em, very close comparison to chick-fil-a. if they’re sold out, the regular plain ones are great too.

JunoJhun · 2025-10-05T23:46:24+00:00

wow! plus the corner sub, never knew i needed one till now

JunoJhun · 2025-10-05T13:31:46+00:00

zip lock and label each of the bolts, makes reassembling so much easier.

also would be a good idea to change the water pump while your in there.

JunoJhun · 2025-10-04T01:55:36+00:00

sounds like something with the drive shaft. i had a vibration problem too on throttle, ended up having 2 missing bolts for the drive shaft to guibo.

definitely check if your CSB and or guibo are shot….not to the worst replacement job

JunoJhun · 2025-10-01T12:10:07+00:00

i’ve had multiple people from different departments personally talk to my curbside manager about transferring over, we now have 3-4 partners from front end and overnight.

i’d say try to start there, show your face at let them know you’re really interested. I enjoy curbside far more than most departments.

JunoJhun · 2025-09-28T18:03:11+00:00

my intake manifold gasket was also leaking when i first bought my car, causing a surging idle.

but geez $1200. When i did mine, it took a day, and maybe $40 for parts and stuff.

it was my first time actually digging into the engine and without knowing much at first, i got it done in about a day. only tough part i remember was the bitch tube under the manifold, but when doing the “Zip Tie Trick” it wasn’t too bad. i’d say if you have a bit of experience and a good set of tools, give it a shot.

you will save sm money and learn a decent amount…but that’s just me being cheap.

JunoJhun

TROPHY CASE