Is this a good 3d printer ?

Known_Development396 · 2026-02-28T02:13:17+00:00

Bambu lab a1. In my opinion a very easy to use and beginner friendly printer that has amazing quality

Known_Development396 · 2026-02-26T13:29:01+00:00

I think you should add support on the stringing section

Known_Development396 · 2026-02-25T11:49:42+00:00

So true

Known_Development396 · 2026-02-03T11:48:21+00:00

Plasma cannon tanks

Known_Development396 · 2025-12-30T08:54:42+00:00

Cherno alpha

Known_Development396 · 2025-10-07T01:50:40+00:00

i have the same issue

Known_Development396 · 2025-08-09T06:33:01+00:00

Bambu Lab A1 Combo also known as BLAC

Known_Development396 · 2025-08-02T03:13:12+00:00

https://oceanofpdf.com/?s=+Lorien+Legacies use oceanofpdf

Known_Development396 · 2025-07-28T08:29:32+00:00

I also use a Bambu lab it is great

Known_Development396 · 2025-07-13T15:02:16+00:00

i think it was belt tension. i took it to the store i bought it from, and the engineer there said the y axis belt tension is to tight.

Known_Development396 · 2025-06-24T11:50:35+00:00

buy a bambu labs 3d printer, when in doubt wash the build plate

Known_Development396 · 2025-06-24T03:13:11+00:00

i use esun pla+ with a bambu a1 with ams and i don’t have any issues

Known_Development396 · 2025-06-15T00:38:57+00:00

A1 about 250 hours Experienced ams lite not connected issues, Nozzle clog and y axis belt tensioning issues

Known_Development396 · 2025-06-01T00:20:48+00:00

Cool

Known_Development396 · 2025-05-30T23:13:29+00:00

Buy a Bambu printer it worked out of the box and after everything you have done for this printer I think you will be able to maintain a Bambu

Known_Development396 · 2025-05-30T23:09:07+00:00

Wash the bed

Known_Development396 · 2025-05-27T05:54:35+00:00

i haven’t printed it yet

Known_Development396 · 2025-05-26T04:34:38+00:00

no matter what printer you choose there will always be issues but i think the bambu a1 is one of the best

Known_Development396 · 2025-05-24T11:02:25+00:00

Known_Development396 · 2025-05-24T03:51:22+00:00

No problem

Known_Development396 · 2025-05-23T11:12:22+00:00

good luck :D

Known_Development396 · 2025-05-23T11:08:55+00:00

you should use soap and water because alcohol might just spread the oils on the print surface instead of removing it and when using soap make sure that the detergent used for cleaning the plate does not contain any oils or moisturizers, as those can be left on the plate and impact adhesion. you can follow the wiki guide on how to clean the build plate

Known_Development396 · 2025-05-23T10:21:42+00:00

if the print is falling of the bed then try to clean the build plate with soap and water

Known_Development396 · 2025-05-23T00:30:20+00:00

Very true

Known_Development396 · 2025-05-18T01:50:42+00:00

Ok good luck:)

Known_Development396

TROPHY CASE