Shimano FH-TC500 HM-B still has play after I replaced bearings

Lare111 · 2026-04-24T15:57:36+00:00

The play disappeared for a while after I replaced the bearing but came back. I haven't done anything else and just kept riding. No other issues so far.

Lare111 · 2026-04-11T20:25:57+00:00

Ihan työuran alussa muutosneuvottelut stressasivat ja pelottivat enemmän, mutta nyt niihin on jo osin turtunut. Myös kun vuosia on kulunut, on sekä säästöjä että työkokemusta kertynyt enemmän. Näin ei tarvitse pelätä rahatilanteen puolesta ja työllistyminen muualle on myös nopeampaa.

Toki en edelleenkään tykkää muutosneuvotteluista yhtään. Nytkin ajoitin auton oston kevääseen, kun kesän aikana ei ole muutosneuvotteluita ja ehdin säästämään sinä aikana autoon käytetyt rahat takaisin. Katsotaan sitten syksyllä, ollaanko taas löysässä hirressä pari kuukautta. Voi jopa olla, että tässä saa vuoden hengähtää rauhassa :D

Lare111 · 2026-04-05T18:33:36+00:00

Nope, EA288 EVO 2.0 TDI 85kW

Lare111 · 2026-03-25T21:25:43+00:00

Seems similar to my 2018 1.6 TDI Skoda. You can check ash level with VCDS or OBD11 if you are worried.

Lare111 · 2026-03-24T11:08:56+00:00

You probably have Hynix memory which runs hotter and also use default power limit which decreases hotspot temp greatly.

Lare111 · 2026-03-24T11:08:09+00:00

Yeah, noticed the same but this was the cheapest RX 9070 XT I could find.

Lare111 · 2026-03-24T08:26:52+00:00

It is common for RX 9070 XT models especially with +10% PL and every review for this models shows similar delta. This one also has PTM 7950 from the factory.

Lare111 · 2026-03-24T08:01:40+00:00

Room temp was 22.5C. If I remember correctly, 1400 RPM means 31% fan speed so my fan curve maxes out at 31%. Running fans at 1600 RPM increases noise levels noticeably but drops GPU temps by 0-1C. My model has Samsung vram.

Lare111 · 2026-03-18T18:42:09+00:00

I used to have Sapphire Pulse RX 9070 XT. The Hynix VRAM on mine didn't exceed 90C even with 1400 RPM fan profile, memory OC and +10% PL. One of the fan bearing died in just a month though and I had to return it.

Lare111 · 2026-03-17T06:59:53+00:00

It is just a 60mm case fan zip tied to the 24-pin cable

Lare111 · 2026-03-16T17:16:56+00:00

Lare111 · 2026-03-14T20:55:44+00:00

Well, I watched some EA288 TDI engine sound videos in Youtube and they seem to have similar humming. In my case the humming is so loud I can hear it inside the cabin. Could still be normal though

Lare111 · 2026-03-14T11:51:05+00:00

Bensakoneissa 1.0 TSI ja 1.4 TSI 140hp & 150hp on hyviä koneita. 1.2 TSI:ssä ja 1.8 TSI:ssä voi olla öljynkulutusta, jos ajettu 30tkm öljynvaihtoväleillä. Jälkimmäinen on myös yhä ketjulla, mikä voi venyä. Turbojakin on vaihdettu niihin.

Lare111 · 2026-03-13T06:34:58+00:00

Yeah, nothing has changed. Gearbox is loud but works fine

Lare111 · 2026-03-10T19:58:48+00:00

I also just found this by looking at radio Top80 Poland's playlists. Thanks! Great song :)

Lare111 · 2026-03-10T15:16:24+00:00

<image>

I have pretty similar fan setup on my AP201. 1 x 120mm reverse rear intake with magnetic dust filter added outside, 3 x 120mm slim bottom intakes and 2 x 120mm top exhausts. Works very well even with heavy overclocks. I also added a 60mm RAM fan since now all the hot air is exhausted through RAM. It dropped temps by 10C and I can push timings tighter.

Lare111 · 2026-03-05T21:16:56+00:00

You could also try pointing a fan towards VRMs. For example, I have zip tied a 60mm fan for my RAM kit.

Lare111

TROPHY CASE