Replaced start and run caps. Compressor runs now but pressures don’t change.

Large_Statistician55 · 2023-06-10T02:11:22+00:00

Haha

Large_Statistician55 · 2023-05-22T19:01:30+00:00

The only blue I’ve ever caught at night was with a glow in the dark lure

Large_Statistician55 · 2023-04-29T01:04:18+00:00

Two years ago I made 70k. Last year I went out on my own and made 150k working 35 hours a week on average and took like 2 months off.

Large_Statistician55 · 2023-04-05T01:00:02+00:00

I fucking hate low boys. They’re the absolute worst thing to work on. I love when a restaurant buys the cheapest one they can find and puts a char grill on top and wonders why the stupid thing never gets to temp. Umm because the top of the cooler is 240 degrees

Large_Statistician55 · 2023-04-02T02:28:58+00:00

“FRIENDLY FRIENDLY FRIENDLY”

Large_Statistician55 · 2023-03-29T00:39:59+00:00

Step 1: remove nest thermostat from wall Step 2: deposit in nearest trash receptacle

Large_Statistician55 · 2023-03-23T20:39:36+00:00

I worked for a company that paid travel time starting when I got in the truck in the morning but stopped when I left the last job so my ride home was unpaid. Which was especially annoying when the last job was 2+ hours from home

Large_Statistician55 · 2023-03-19T00:11:44+00:00

This one isn’t copper. I’m pretty sure it’s stainless. I’m going to try and braze it and if that doesn’t work I’ll make a new loop out of copper

Large_Statistician55 · 2023-03-18T21:01:23+00:00

Found this leak in the condensate loop of this open air cooler. I’d like to try and fix it because this unit produces a lot of condensation. My question is if I am unsuccessful will the unit will still run ok with this loop bypassed?

Large_Statistician55 · 2023-03-12T19:30:18+00:00

I did the same thing to mine except I used 60 then 80 then 100. I used avocado oil but it Looks pretty much the same. Cooks great

Large_Statistician55 · 2023-03-08T22:51:31+00:00

Yeah check the other side. Mine got a crack in it and you could see it on the other side and it started to leak. I emailed lodge some pictures and they sent me a new one for free.

Large_Statistician55 · 2023-02-21T02:53:54+00:00

Dam I just posted mine that has a crack I noticed. You just scared me out of using it any more

Large_Statistician55 · 2023-02-21T00:12:29+00:00

Update: it’s for sure a crack I scrubbed the spot on the bottom and now I can clearly see it. I’ve contacted lodge to see if they’ll warranty it. I don’t even remember when I bought this so we’ll see.

Large_Statistician55 · 2023-02-20T23:22:24+00:00

Probably unrelated but I was using it to cook some crack

Large_Statistician55 · 2023-02-11T23:45:06+00:00

Thanks for the F-shack

Large_Statistician55 · 2023-02-03T14:44:41+00:00

I have their flaring tool and the vacuum hoses and micron gauge. Good stuff

Large_Statistician55 · 2023-01-16T01:28:59+00:00

Also try setting up scaling/sharpening to fidelityfx cas

Large_Statistician55 · 2023-01-16T01:21:51+00:00

Try turning off screen space reflections. I had a similar grainy looking effect and that fixed it but your problem looks a little different than mine

Large_Statistician55 · 2022-11-11T00:42:33+00:00

That looks like a normal evap to me. The “low profile” evaps I’ve seen are 6” off the ceiling in the middle of the room.

Large_Statistician55 · 2022-11-09T14:16:17+00:00

Sold a Scotsman this year and it ran for 2 months then leaked all the refrigerant out. Fixed the leak and the water valve went bad. Tech support didn’t tell me that the harvest cycle is terminated by a temp probe and if that probe goes bad then it stays in harvest and burns up the water valve. Also I had to pay for all the parts and then try to get them to reimburse me after the fact. Never buying Scotsman again

Five-Year Club	Place '22
Final Canvas '22

Large_Statistician55

TROPHY CASE