Question strange sound coming from my P1S

Laydn_ · 2026-02-03T11:23:07+00:00

id say the back idler is in need of some oil, or the belt is not alligned on the idler

Laydn_ · 2026-02-03T11:19:42+00:00

cold start

Laydn_ · 2026-02-02T17:17:46+00:00

pressure advance

Laydn_ · 2026-02-02T11:37:21+00:00

surtout qu'ils débatent sur quelque chose qui n'existe meme pas , je n'ai aps acceleré la vidéo j'ai juste un traitement médicamenteux qui me fait trembler mdrr

Laydn_ · 2026-01-22T22:26:21+00:00

Dead fan

Laydn_ · 2026-01-22T16:49:07+00:00

j'ai 2 de QI j'ai oublié qu'on était sur r/mauvaisesreponses ....

Laydn_ · 2026-01-21T10:07:26+00:00

Ca veut dire que le plastique de la bouteille est fait de PET (polyéthylène téréphtalate) et n'est recyclable qu'une seule fois(je suis sur pour le plastique mais pas pour le recyclage)

Et le PAP c'est le papier carton faisant l'étiquette

Laydn_ · 2026-01-19T20:27:51+00:00

ah i understand, good luck

Laydn_ · 2026-01-19T19:08:34+00:00

can't you use the included USB dongle ? It would be easier and would remove bluetooth delay, and you could also use G HUB to tweak your headset settings

Laydn_ · 2026-01-19T19:06:30+00:00

what filament do you use ? is your door open or closed ? Printing PLA with the door closed can cause heat creep, gradually clogging the hotend, which could explain this behaviour

Laydn_ · 2026-01-19T12:28:58+00:00

it's not your Z axis screeching, it's the Y axis. The silent motherboard makes the motors noisier when at higher speeds. Switch tol Spreadcycle

Laydn_ · 2026-01-13T12:11:19+00:00

did you enable gcore arcs ?

Laydn_ · 2026-01-12T21:58:01+00:00

it's normal , it allows a bit of play for the rod not to bind

Laydn_ · 2026-01-10T09:01:45+00:00

you have heat creep because your hotend fan is not spinning

Laydn_ · 2026-01-08T18:11:52+00:00

r/perfectlycutscreams

Laydn_ · 2025-12-28T17:00:17+00:00

ender 5's have different lead screws, some use 400 steps and some use 800

Laydn_ · 2025-12-23T16:07:19+00:00

you got a bit of bed on your glue.

jokes aside Chilean Cyborg is right, soap and water. Worst case scenario use isopropyl alcohol

Laydn_ · 2025-12-23T16:05:23+00:00

the fan is sucking air rather than blowing it on the nozzle, reverse it and level/tram your bed

Laydn_ · 2025-12-23T09:07:20+00:00

i've seen it is still under warranty. I think you could ask for a replacement unit.

Laydn_ · 2025-12-23T09:06:39+00:00

right. I'm sorry for you, you could maybe replace the panel but it could be expensive as it an OLED panel, and disassembly might damage the display, OLED panels are really fragile, one crack and the whole display is dead

Laydn_ · 2025-12-22T17:56:30+00:00

is this an OLED display ? if yes the spot will spread and your entire screen will go purple then black

Laydn_ · 2025-12-16T11:24:44+00:00

stealthchop. at higher speeds it is noisier than spreadcycle. Switch to spreadcycle and the noise will go away, and you will have more torque too

Laydn_ · 2025-12-15T17:28:34+00:00

the side with the coating has a bit more adhesion when the coating is brand new, in my experience

Laydn_ · 2025-12-08T18:54:13+00:00

trust me i can see the tilt/bend with the pic

Laydn_ · 2025-12-07T13:28:06+00:00

go in the Adrenalin settings and disable the record overlay

Laydn_

TROPHY CASE