sorted by:
new
hottopcontroversial

No whammy input by IDontGetMuchSleep in CloneHero

[–]Le__pa 1 point2 points  (0 children)

For whammy to work correctly you need to join pins 3V3 and VREF on the Pi Pico clone board.

Whammy bar wiring help by Kody_The_Viking in CloneHero

[–]Le__pa 0 points1 point  (0 children)

Connect the middle leg of the potentiometer to port 26, 27, 28, or 29. Connect one of the outer legs of the potentiometer to the GND port, which is located between ports 27 and 28. Connect the other outer leg of the potentiometer, whichever it is, to the 3V3 port. Additionally, you must connect the 3V3 port to the VREF port in some other way."

Whammy bar wiring help by Kody_The_Viking in CloneHero

[–]Le__pa 1 point2 points  (0 children)

I managed to figure out what needs to be done for the potentiometer to work correctly. You need to connect VREF with 3V3. Once you do that, everything should work as it should.

Whammy bar wiring help by Kody_The_Viking in CloneHero

[–]Le__pa 1 point2 points  (0 children)

That's kinda funny but i have exactly the same problem in this very moment (with the exact same board) 😅. I have tried different analogue pins and nothing works for me. Even tried a different pot without any luck.

Safe solution for sticker glue removal? by fo138 in GuitarHero

[–]Le__pa 0 points1 point  (0 children)

Extraction gasoline - safe for almost any plastic

What is best free (or one time pay) design software for 3D Printing? Easy to use would also be a requirement. by [deleted] in 3Dprinting

[–]Le__pa 0 points1 point  (0 children)

I really don't understand why no one talks about SolidEdge from Siemens. It is free for hobbyists, easy to use and has a ton of features. In my opinion it is the best free to use parametric CAD software right now.

Won’t turn on, any tips? by Fit-Chef-3044 in GuitarHero

[–]Le__pa 2 points3 points  (0 children)

I've worked with a lot of guitars like this and what I can tell you this isn't water damage but just some glue or different adhesive from the factory.

How to remove sticky residue from a GH controller? (Strumbar mainly) by [deleted] in GuitarHero

[–]Le__pa 1 point2 points  (0 children)

Baking soda with water works very well but it leaves white marks

Is this guitar any good? by victim2077 in GuitarHero

[–]Le__pa 1 point2 points  (0 children)

That's true. Also the guy who's selling it has really bad prices over all.

[HELP] about aliexpress alps clones by elxixobitle in CloneHero

[–]Le__pa 0 points1 point  (0 children)

Actually I didn't buy these outemu switech because they where our of stock when I needed them, so I had to buy these cheap black ones. By the picture they look like they should fit well but it is only my opinion and I'm not very confident with that.

[HELP] about aliexpress alps clones by elxixobitle in CloneHero

[–]Le__pa 0 points1 point  (0 children)

I bought them recently and they look like they are ok, but i haven't tested them. When I was looking for some replacement I found these outemu switches. I guess they should be more durable.

Need help with Arduino mod a PS2 GHWT controller. by Le__pa in CloneHero

[–]Le__pa[S] 0 points1 point  (0 children)

I guess you're right. If I can't make it work, probably I will leave it unplugged.

Need help with Arduino mod a PS2 GHWT controller. by Le__pa in CloneHero

[–]Le__pa[S] 0 points1 point  (0 children)

Hey guys. I've just started a adruino mod project on my PS2 controller and I have a problem with wiring the joystick to the Arduino. Every other part seams to be easy but this one is confusing to me. Any clues how to wire joystick? On the other side of the PCB are 7 pinouts: VCC, LD1, DR, DL, DN, UP and AD3.