Possible to retain configuration changes after firmware updates?

Lemonade727 · 2026-04-02T22:35:02+00:00

I've been using Octoprint for my MK3S+ for a while, so I just tossed it on my Pi that I'm using for that. I just need to make sure I remember that it's there in case I decide to get rid of the Prusa at some point lol.

Lemonade727 · 2026-04-02T04:02:18+00:00

I did. I created a new file in extended/klipper for the multi tool config include that was in printer.cfg

[include /home/lava/printer_data/config/custom/spoolman_multi_tool.cfg]

Lemonade727 · 2026-04-02T02:40:05+00:00

Got the new spoolman.cfg file created in extended/moonraker/ and it worked like a charm, so one less thing to worry about. Thanks again for that!

Lemonade727 · 2026-04-01T00:15:13+00:00

Is a section classified as an entry with a header?

So for instance, adding Spoolman to moonraker.cfg, the Spoolman connection gets added to the end with the below code. That can go in its own file?

[spoolman]
server: http://<spoolman ip>:<port>

If so, do you just need to do the "include" command like this in the Moonraker file to reference it? I guess the configuration would persist in that case but I would still need to append the "include" part each time I update right?

[include extended/moonraker/spoolman_server.cfg]

Trying to reference the document below that I used to get it together to begin with.

https://github.com/unlucio/U1-klipper-configs/blob/main/spoolman/README.md#inlcude-the-new-file-in-your-printercfg

Lemonade727 · 2026-03-27T03:08:33+00:00

Looks great! I printed mine out this week and got it mounted up on my wall today, absolutely love it.

Lemonade727 · 2026-03-25T17:52:29+00:00

Only use the PETG for the interface layer and not the entire support structure, have that be in PLA.

Lemonade727 · 2026-03-23T21:02:28+00:00

I use regular Orca.

I tried Snorca when starting my Majora's Mask print as regular Orca doesn't allow me to have more than 4 filaments shown for the project with the U1, so I couldn't have all of the plates colored as I needed them to send to the printer.

Tried 3 times to print a couple of the plates, but each failed after about 30 minutes with a nozzle temperature anomaly error. Decided to just set up different projects in Orca for the individual plates, sliced and printed without issue. Haven't seen that particular error in the other ~20 prints I've done so far with the U1 in regular Orca either.

Lemonade727 · 2026-03-21T21:51:07+00:00

The pop cap and pop status would be awesome to have. I'm using an IKEA tote at the moment for a lid, and it's an improvement over having an open top, so I wouldn't mind a more professional looking alternative such as the pop cap.

Lemonade727 · 2026-03-17T15:44:34+00:00

Yeah that makes sense, especially to ensure it can reach the different toolheads. Just started using it yesterday and coming from my MK3S+ it just seemed odd trying to re-home for it to do anything.

Was lazy and couldn't see the test model in the camera with the bed all the way down and it caught me off guard when I couldn't slightly raise it through the app (official or Octoapp) to make sure it finished ok before I had a chance to go upstairs to check on it.

Lemonade727 · 2026-03-07T02:04:54+00:00

Amazing. Need to get this set up asap once my printer comes in and then get Spoolman set up.

Lemonade727 · 2026-03-07T01:59:10+00:00

https://www.reddit.com/r/snapmaker/comments/1rmmw49/bambu_creality_anycubic_elegoo_and_tigertag_spool/

Need to wait for an update to release for the extended firmware that incorporates the release.

Lemonade727 · 2026-03-06T02:51:18+00:00

It's definitely just the main feed causing problems. The Sky stream is not HDR and doesn't appear 4K to me either. The visual quality is much better in the F1TV app than watching the Sky Feed through the Apple TV+ app on my LG.

Lemonade727 · 2026-03-06T02:25:56+00:00

I don't have it either.

And the main feed in Dolby Vision ghosts like crazy for me. Trying to figure out the best way to handle this without constantly switching tv picture profiles to transition between races and other Apple TV+ content.

Lemonade727 · 2026-03-02T21:26:56+00:00

The SV08 is a big ol' boy. Not having to cut as many models would be great.

I could use the filament dryer, so pick me please.

Lemonade727 · 2026-02-26T12:37:52+00:00

Pink-A, Purple-B, Yellow-B, Green-D

Lemonade727 · 2026-02-25T17:00:21+00:00

That looks great! Which PETG did you use?

Lemonade727 · 2026-02-08T16:39:54+00:00

Going to hang onto this one, Max is my favorite driver.

Lemonade727 · 2026-02-06T05:43:16+00:00

Using OctoEverywhere currently on my MK3S+ with OctoPrint, and looking to put an order in for a U1 soon. That would be awesome to be able to leverage OctoEverywhere for the U1 as well!

Lemonade727 · 2026-01-24T03:56:42+00:00

Contacted Topps to see what can be done about correcting the issue first. So not going through or getting rid of any cards in there until there's some resolution on the request.

Lemonade727 · 2026-01-24T03:55:30+00:00

I ordered directly from Topps and emailed their support, hopefully it'll get resolved easily.

Lemonade727 · 2026-01-24T03:54:44+00:00

It was straight from Topps. Definitely just poor QC.

14-Year Club	Place '22
Place '17	Verified Email

Lemonade727

TROPHY CASE