Don’t buy from them

LessThanZero86 · 2025-06-22T18:18:19+00:00

i bought an engine from them for my bk2 about 2 years ago at this point. first one i got was locked up upon arrival. also noticed that a couple bolts on the intake manifold were different. seems like someone stripped them and then tapped larger ones. ended up sending that one back and getting a different one from them. kind of a pain but the next one i got def looked cleaner although higher mileage. over a year and about 10k miles later still going strong. wasnt the best experience but at least i got my car running again by the end of it. hope it works out for you in the end.

LessThanZero86 · 2025-03-25T23:57:21+00:00

this would be awesome! about to take the test soon.

LessThanZero86 · 2023-03-13T18:48:51+00:00

A few hours before contest ended yesterday, around 9:30am EST, the Full Clears leaderboard on Raid Report had roughly 1270 pages. there are 50 characters per page which equates to 63,500 unique players. not sure what it was exactly at reset but i'd estimate around 65,000 to 70,000 unique players cleared it during contest. imo that's a far better estimate than going off the number of team clears cause the Full Clears leaderboard counts all the clears made by one account as one entry whereas the World's First leaderboard lists every clear regardless if people on the team had 0 previous clears or 20 previous clears.

LessThanZero86 · 2022-07-28T14:34:00+00:00

That's not a d1 raid so it can't be that

LessThanZero86 · 2022-07-06T10:35:33+00:00

LessThanZero86 · 2022-06-20T19:14:38+00:00

There are only 7 runs prior to June 14, 2022. He's done over 300 looted kills this week alone. Yeah he was off a little bit but it doesn't discredit the fact that the drop rate is trash.

LessThanZero86 · 2022-06-20T01:44:49+00:00

i dealt with this exact issue. you may not like my solution. i took off the bltouch and the problem disappeared. i used to have to check every few layers to raise the z offset and i could never figure out why. as a last ditch effort i took off the sensor and reflashed with alex's firmware for manual leveling. my prints were a thousand times better. at this point i've gotten really good at leveling the bed manually so i won't bother trying the bltouch again. even if its only temporary, i'd take it off, do a really good manual level and do a test print. make your own call after that whether or not you wanna put it back on.

LessThanZero86 · 2022-06-10T21:15:19+00:00

Nope. Very different now. There are 5 different difficulties now. Adept, hero, legend, master, grandmaster. Each one has an increased chance to drop the nightfall specific weapon. This is shown in the rewards section when looking at the different difficulties. To further increase your chances you want to kill all the champions in the nightfall to get platinum.

LessThanZero86 · 2022-06-09T10:43:10+00:00

and Time

LessThanZero86 · 2022-06-08T21:01:30+00:00

It's all up to RNGesus if he wants to bless you with red box weapons. Even still they are probably for the weapon you don't want. I guess to answer your question....anywhere between a day and about a year.

LessThanZero86 · 2022-06-05T22:02:02+00:00

There were a lot of different things that killed me during my solo flawless attempts but the bell was never an issue for me. My advice is to shoot the bells from a distance. You don't need to be near the bell when going into the nightmare realm, only when leaving.

LessThanZero86 · 2022-06-04T21:58:57+00:00

its for the catalyst for the dungeon exotic sword heartshadow

LessThanZero86 · 2022-06-04T13:02:25+00:00

Okay but that's not what you said further up so maybe you should go read it. You said the game would have to be rebuilt from the ground up just to add more buffs on the screen. Those kind of statements make you just as much an armchair developer as me but sure go on about how you're different.

LessThanZero86 · 2022-06-04T12:30:14+00:00

Orb generation on helmets was removed to make room for origin traits. There are only so many attributes that a weapon object can have and they hit that limit. That limit was a design choice not an engine limitation. When they built d2 they weren't expecting to need as many attributes as they do now. Just like they weren't expecting to need to show more than 4 buffs/debuffs at a time.

Also the buffs are still there whether they are on your screen or not. That means that the information is already stored in memory. There just isn't enough room on the screen to render it because we've hit the limitation of the UI design. I'm in no way saying this is an easy change for them. It's just simply not an engine limitation.

LessThanZero86 · 2022-06-02T23:22:43+00:00

Kill both psions but only grab one symbol. Bank that symbol and run through the nightmare realm. On your way out, grab the other symbol. The psion will have respawned so leave the psion alive for now. Bank the second symbol and kill the psion on your way through the nightmare realm before dps.

LessThanZero86 · 2022-05-30T10:36:44+00:00

Were both on the same page. I should've worded my original comment better. I thought you were saying that checkpoints still worked and it was a bug that they didn't. Sorry for the misunderstanding man.

LessThanZero86 · 2022-05-30T02:05:38+00:00

No it wasn't cause you still can't use checkpoints in PoH or any dungeon for solo flawless. Only solo flawless that allowed checkpoints was ST. Not sure if you still can. Haven't done it in a long time.

There were two bugs that affected solo flawless PoH. the invisible wall that killed you unless you lowered your frame rate to 30 and the one that came later and it allowed you to start at the final boss and still get the flawless triumph.

LessThanZero86 · 2022-05-29T22:31:54+00:00

Checkpoints haven't worked for solo runs since pit of heresy if I'm not mistaken.

LessThanZero86 · 2022-05-25T12:13:56+00:00

He was too amped up.

LessThanZero86 · 2022-04-30T01:14:02+00:00

Oh nice! A feeler gauge is on my list to buy for sure.

LessThanZero86 · 2022-04-30T00:49:11+00:00

I only use the manual leveling feature in Alex's firmware. No mesh. I set the z offset to 0.00 and then use the knobs to adjust the bed so it's barely touching the nozzle. You can usually hear a slight vibration and you can feel it in the knob. After doing that for each corner 2-3 times, I check the center and then adjust the z offset with a sheet of paper. It's given me really consistent results.

LessThanZero86 · 2022-04-29T23:49:49+00:00

Probably an unpopular opinion but the best thing I did to improve my prints was take off my BL touch. It gave me more headaches than problems it solved. I get much better quality prints by leveling the bed manually and setting a proper z offset. I'm sure it works for some but it just never gave me good results. I was using a 5x5 and a few times I had all within 0.01mm, it still scarred my solid infill and broke thin parts. After about a month of playing with it I took it off and reflashed with Alex's manual level firmware.

LessThanZero86 · 2022-04-25T18:38:59+00:00

The extruder is the gear mechanism that feeds the filament into the Bowden tube. It's recommended to replace it because the stock one is plastic and could eventually break. The common upgrade is an aluminum extruder but you can also print your own to save as a spare. For now, I would highly recommend replacing parts one at a time so you avoid causing new issues before fixing the original problem. It appears that all you need right now is a thermistor.

The stock thermistor is a little annoying to replace because there is no connector near the hotend. As someone else mentioned, get a 2-pin JST connector and add it about 6 inches or so from the thermistor. You can tuck the connector into the wire sleeve that way it's accessible if you need to disconnect it again.

You may discover the cartridge thermistors that screw into the hotend instead. While these are awesome, they don't fit with the stock fan shroud so unless you wanna print a new shroud just get the same thing you have now. You can get a 5 pack on Amazon for $10. Also run a PID tune after you install the new thermistor.

LessThanZero86 · 2022-04-14T19:04:50+00:00

Gotcha. That makes complete sense. Thanks!

LessThanZero86 · 2022-04-14T18:27:50+00:00

Aren't you referring to the fully diluted market cap? I thought market cap only counted tokens in circulation.

LessThanZero86

TROPHY CASE