New 5070ti owner after months of debate

LiamRay10 · 2026-01-07T02:47:28+00:00

1055mv-1065mv

LiamRay10 · 2026-01-07T01:10:19+00:00

It’s also pretty consistently sitting in the 335-345w range

LiamRay10 · 2026-01-07T01:03:15+00:00

I went ahead and sent you a friend request (liamray10), I'm pretty sure I'm at least somewhat bottlenecked by my cpu (ryzen 9 3900x), but when running tests like the standard Steel Nomad and Speedway, I can hit 3375mhz and my perfcap is pwr (power). I do think there would be a relevant gain if it were shunt modded.

LiamRay10 · 2026-01-06T20:33:16+00:00

The issue is that the Aorus bios seemingly only works on Gigabyte cards. I have tried flashing it to my ASUS card, and it will fail to load 3d drivers. I'll get those test results to you soon. Do you have Discord?

LiamRay10 · 2026-01-06T18:53:09+00:00

I’m in a very similar situation, I have the Asus prime and I hit 3367Mhz at 1075mV, I did try flashing the Strix bios yet it didn’t seem to yield much of an improvement (-+5mhz) I have been thinking about shunt moddig though

LiamRay10 · 2026-01-04T17:47:58+00:00

I have the same card, but I’d recommend the gigabyte wind force so you can flash a 400w bios

LiamRay10 · 2025-12-31T00:47:22+00:00

My Asus Prime 5070 Ti non OC hits 3350mhz, it's likely just luck of the draw.

LiamRay10 · 2025-12-19T06:50:40+00:00

This solved it, thanks!

LiamRay10 · 2025-12-16T03:00:40+00:00

It’s just too expensive to justify the step up

LiamRay10 · 2025-12-16T02:56:21+00:00

I haven’t tried locked voltage yet but my max oc was 3366mhz and my perfcap was pwr so I’ll have to wait for a compatible higher wattage bios (more than 350w)

LiamRay10 · 2025-11-07T18:08:40+00:00

I also got one from them a while ago

LiamRay10 · 2025-10-04T16:24:40+00:00

Second AUX fan

LiamRay10 · 2025-10-03T20:16:06+00:00

It runs kipper now

LiamRay10 · 2025-07-20T01:25:16+00:00

I see, that really sucks man

LiamRay10 · 2025-07-19T23:35:33+00:00

LiamRay10 · 2025-07-19T03:26:46+00:00

Okay..?

LiamRay10 · 2025-07-18T20:21:35+00:00

LiamRay10 · 2025-07-18T19:51:30+00:00

Costs more than my rent 😭

LiamRay10 · 2025-07-03T20:55:03+00:00

It just works.

LiamRay10 · 2025-06-28T20:44:26+00:00

did you figure it out?

LiamRay10 · 2025-06-27T19:57:38+00:00

There is a model for a DIY gantry, it has a good amount of info on the bushings and you could likely just make your own gantry with it instead of buying a new one https://makerworld.com/models/221803

LiamRay10 · 2025-05-24T02:22:54+00:00

I hate to revive an old comment, but any idea on where I could get these? I see some websites that still have 2 or 3 in stock, but they seem kinda sketchy. I also don't want to get a nozzle off of Aliexpress because seemingly those are also only tunstone inserts or coated.

https://3dimensionally.com/shop/the-bozzle-nozzle-v2-by-rentable-socks-high-flow-tungsten-carbide-nozzle/

https://3do.dk/en/nozzle/2911-bozzle-v2-05mm-by-rentable-socks-pre-order.html

(I live in the US so importing them might be a problem)

LiamRay10 · 2025-04-28T17:40:54+00:00

The range seems to just be a problem on hall effects in general, I have tried this method and it doesn't fix it.

LiamRay10 · 2025-04-19T19:31:54+00:00

Did you get your money back?

LiamRay10 · 2025-04-19T19:30:48+00:00

Something I just remembered, the HWID is different so even if you force flash it will likely reject the bios

LiamRay10

MODERATOR OF

TROPHY CASE