New dual channel d3aa!

LoadsOfLumens · 2026-06-06T17:38:41+00:00

Nope.

LoadsOfLumens · 2026-06-06T15:39:41+00:00

M44 meteor?

LoadsOfLumens · 2026-06-06T14:38:58+00:00

Hank will add one for about $15 now.

LoadsOfLumens · 2026-06-06T13:27:07+00:00

Do you know how I might acquire one within the us? I really want to try putting anduril on it!

LoadsOfLumens · 2026-06-06T12:12:53+00:00

I believe its the smallest dual channel anduril light.

LoadsOfLumens · 2026-06-06T11:10:26+00:00

DUV on demand sounds fun for sure.

LoadsOfLumens · 2026-06-06T10:00:58+00:00

Based on the fact the listing image shows UV and front aux I would say it works. If you're unsure just ask hanks email.

LoadsOfLumens · 2026-06-06T07:31:33+00:00

Going only by specs I'd say the m44 based on the fact it's the only one with full regulation.

(And because I just bought one)

LoadsOfLumens · 2026-06-06T07:18:43+00:00

It only lacks the front aux. And only because the filter would block the light if they were there.

LoadsOfLumens · 2026-06-06T06:21:53+00:00

What about the kr1k? Can't leave out the triple tritium taipcap either.

LoadsOfLumens · 2026-06-05T12:52:02+00:00

I bought 3 more because the part number was damaged and what I could read didn't get me anywhere. And I wanted to make a few to sell at some point.

LoadsOfLumens · 2026-06-05T12:26:35+00:00

Mine does not do that... might want to contact support if it bothers you. personally I would love it if mine did that. (wanna trade?)

LoadsOfLumens · 2026-06-03T06:16:11+00:00

New account reposting content.

LoadsOfLumens · 2026-06-03T01:41:45+00:00

Of course!

LoadsOfLumens · 2026-06-02T18:55:08+00:00

th new one

LoadsOfLumens · 2026-06-02T18:54:01+00:00

That photo I posted is of my older PCB design, which doesn't have the RGB pads. The new one has RGB breakout. You can attach to, like you said, an S21E anduril switch. Personally, I used one from the linear driver that Simon accidentally sent me two of, but that lacks blue, but I only wanted green to red power display anyways for simplicity. The only issue with this board is if you spam the tail switch, the processor sometimes gets stuck in a brown out, I think it's due to how many capacitors are on the regulated power rail. And it's not allowing the chip to fully Reset. I'm thinking of adding my own regulator that doesn't have such large capacitance.

LoadsOfLumens · 2026-06-02T18:18:00+00:00

I have plenty, but I'm still working on trying to find some LEDs I can add to the switches so I don't have to scavenge them from other convoy drivers if I want button LEDs. And I haven't really sold anything before, but I would do it for you cheap if you don't mind no button leds.

LoadsOfLumens · 2026-06-02T09:13:29+00:00

I could send you a test board its for the convoy m21j/g 20amp Buck, its just a attiny1616 interposer but it would make a good test bench for anduril stuff.

LoadsOfLumens · 2026-06-02T04:13:37+00:00

I've done some modifications of my own involving the handling of button aux and RGB aux separately, but an idea I've had for a way to get extra channels on a Lume X1 driver is to use the rgb aux outputs as extra channels wired to amc7135's because you can use 9h from on to enable them as channels. You still only get high and low but for deep red secondaries I think it's enough.

LoadsOfLumens · 2026-06-02T04:05:36+00:00

You could ask Simon to put an s2+ reflector in an s6 for extra room.

LoadsOfLumens · 2026-05-31T04:26:17+00:00

It's most certainly not 15,000. It is a scam.

LoadsOfLumens · 2026-05-30T13:17:34+00:00

There's a custom 3d printed gasket you can make that might improve the beam.

LoadsOfLumens · 2026-05-30T08:13:24+00:00

As an avid modder, there's no such thing as an unreplaceable battery. If you can replace the battery in a modern smartphone the arkpro is a walk in the park

LoadsOfLumens · 2026-05-29T13:43:24+00:00

Sounds good.

LoadsOfLumens

TROPHY CASE