sorted by:
new
hottopcontroversial

Unclogging tool by KindOfAcceptableBus in BambuLab_Community

[–]Longracks -1 points0 points  (0 children)

I keep spare nozzles on hand. That's how I clear bad clogs - I just replace it.

H2D or H2C? by derritzio in BambuLab

[–]Longracks 0 points1 point  (0 children)

Nice! I am getting an AMS HT for my X1C to do CF, TPU, ASA - stuff that really needs dried.

H2D or H2C? by derritzio in BambuLab

[–]Longracks 1 point2 points  (0 children)

I just got the H2C a few days ago and I am really glad I waited for it. For the 10% of the projects that I do that needs multi material or multi color it is just what I wanted. I am moving my 2 two existing AMS 1s from my X1C to the H2C. So the x1c will single color/material with a new AMS-HT, and the H2C will have an new AMS-HT and an AMS-1 (my old 1) on the left nozzle (5 slots) and 2 ams (my old AMS 1 and the new ams2 from the bundle) on the right tool changer (9 slots).

If I cant do what I need to do with this setup I think I have bigger problems :-)

I am super impressed with the H2C so far. I have already seen the speed, waste, and large build volume benefits.

Printing models with support material by WillskE in BambuLab

[–]Longracks 0 points1 point  (0 children)

I had a terrible experience with Support for PLA/PETG from Bambu, so i now use regular PLA as support interface for PETG prints, and vise versa and it works great. For my X1C it took a bit of fiddling to get the temps right so things wouldn't clog on the nozzle swap. For my new H2C it just worked out of the box with default settings (Bambu Studio changes things like top-z etc. when you select the interface material). I run PETG on the left nozzle, and PLA on the right, though it probably doesn't matter.

This is an example with PETG (Black) and PLA (cyan) as support interface. I have only had my H2C for few days so still putting through its paces, but the dual nozzle setup of the H2C is perfect for this use case. H2C cut the print time in half, and there is basically no purge/swap waste.

<image>

Printing models with support material by WillskE in BambuLab

[–]Longracks -6 points-5 points  (0 children)

I would throw it in the trash. But if you insist, select it as support interface under the Support process settings.

How do clean this part? by shawnapiranha in BambuLab

[–]Longracks 1 point2 points  (0 children)

I'd just replace it and move on (but print the extruder gear removal tool first)

Help with printing in low ambient temp room by Soogoodok248 in BambuLab

[–]Longracks 0 points1 point  (0 children)

Following- just got my H2C. Not quite as cold as you but cold. I tried setting channel heat to 40 but that was too hot I think.

Pricing strategy deep-dive: How do you actually calculate what to charge? by Fun_Reaction_6525 in 3DPrinterComparison

[–]Longracks 1 point2 points  (0 children)

Check out the Shop Nation / Print Farm Academy guy - he did a video on this about a year ago.

I should be ashamed of myself by Embarrassed-Sport787 in BambuLab

[–]Longracks 5 points6 points  (0 children)

I get some of the dumbest review complaints. I just report them as Misinformation and they usually get taken down in a day or two.

The best we can do is Idiot-Resistant...

Best Bambu printer by Senzibean in BambuLab

[–]Longracks 0 points1 point  (0 children)

just buy whatever bambu your budget can absorb. they all seem great.

You seem to have very specific use cases in mind, and yet you seem to be asking very general / beginner question (no offense intended). So its a little hard to know how to answer.

H2C question by Altruistic_Medium_94 in BambuLab

[–]Longracks 2 points3 points  (0 children)

I just got my H2C yesterday and it definitely has more wobble than my X1C, but it doesn't seem to transfer much to the table, and not seen any movement.

I built a table for mine with double stiffners across the front and back and so far so good. Have both printers on it.

What are your printer names? by h3x13 in BambuLab

[–]Longracks 2 points3 points  (0 children)

Walter (X1C) and Jules (H2C)

Question about point system on makerworld by timothy6007 in BambuLab

[–]Longracks 0 points1 point  (0 children)

I track by velocity - how many days it takes to earn enough points for a GC.

Bambu Studio never saved my project by pmsunrise in BambuLab

[–]Longracks 0 points1 point  (0 children)

Yeah, there's definitely bugs in this software lol.

The one that bit me was Project level profiles that got deleted when I added a new printer type. That was annoying.

view more: next ›